Now showing items 4181-4200 of 10765

    • Experimental Seismic Performance of Beam-Column Subassemblies Using Ductile Embeds 

      Barbara; Chang; Tara C.; Hutchinson; Xiang; Wang; Robert; Englekirk (American Society of Civil Engineers, 2013)
      When designed according to current special moment frame requirements, conventional RC beam-column joints in frame-braced buildings subject to design level seismic loads suffer severe damage. Construction of these conventional ...
    • Dual-Objective-Based Tornado Design Philosophy 

      John W.; van de Lindt; Shiling; Pei; Thang; Dao; Andrew; Graettinger; David O.; Prevatt; Rakesh; Gupta; William; Coulbourne (American Society of Civil Engineers, 2013)
      Tornadoes represent a unique natural hazard because of the very low probability of occurrence, short warning times (on the order of only a few minutes), and the intense and destructive forces imposed on engineered and ...
    • Seismic Response of Single-Degree-of-Freedom Systems Representing Low-Ductility Steel Concentrically Braced Frames with Reserve Capacity 

      Gang; Li; Larry A.; Fahnestock (American Society of Civil Engineers, 2013)
      Steel concentrically braced frames (CBFs) are used widely as a seismic lateral force–resisting system. Although modern CBFs designed for high seismic regions have considerable ductility, CBFs in moderate seismic regions ...
    • Experimental Performance of Steel Braced Frames Subjected to Bidirectional Loading 

      Keith D.; Palmer; Charles W.; Roeder; Dawn E.; Lehman; Taichiro; Okazaki; Carol; Shield (American Society of Civil Engineers, 2013)
      Concentrically braced frames (CBFs) are stiff, strong systems frequently used to resist seismic loading. Special CBF (SCBF) behavior is dominated by brace buckling, while buckling restrained braced frames (BRBFs) develop ...
    • Influence of Surrounding Buildings on Wind Loads Acting on Low-Rise Building 

      Yong Chul; Kim; Akihito; Yoshida; Yukio; Tamura (American Society of Civil Engineers, 2013)
      A large number of wind pressure experiments have been performed to investigate the influence of surrounding buildings on wind pressures and forces on a cubical low-rise building. The primary purpose of the present work was ...
    • Structural Behavior of Symmetric Spindle-Shaped Tensairity Girders 

      Rolf H.; Luchsinger; Cédric; Galliot (American Society of Civil Engineers, 2013)
      The load-bearing behavior of a symmetric spindle-shaped Tensairity girder with 5-m span and thin chords is studied experimentally, numerically, and analytically. The influence of the air pressure on the load-deflection ...
    • Time-Frequency Blind Source Separation Using Independent Component Analysis for Output-Only Modal Identification of Highly Damped Structures 

      Yongchao; Yang; Satish; Nagarajaiah (American Society of Civil Engineers, 2013)
      Output-only algorithms are needed for modal identification when only structural responses are available. The recent years have witnessed the fast development of blind source separation (BSS) as a promising signal processing ...
    • Performance of Steel Moment Connections under a Column Removal Scenario. I: Experiments 

      H. S.; Lew; Joseph A.; Main; Stephen D.; Robert; Fahim; Sadek; Vincent P.; Chiarito (American Society of Civil Engineers, 2013)
      This paper presents an experimental study of two full-scale steel beam-column assemblies, each comprising three columns and two beams, to (1) define their response characteristics under a column-removal scenario, including ...
    • Negative Stiffness Device for Seismic Protection of Structures 

      A. A.; Sarlis; D. T. R.; Pasala; M. C.; Constantinou; A. M.; Reinhorn; Nagarajaiah; D. P.; Taylor (American Society of Civil Engineers, 2013)
      Structural weakening and addition of damping is an approach previously proposed for the reduction of seismic forces and drifts in the retrofit of structures. It is also used in the design of new buildings with damping ...
    • Design of Steel Storage Rack Columns via the Direct Strength Method 

      Miquel; Casafont; Maria Magdalena; Pastor; Francesc; Roure; Jordi; Bonada; Teoman; Peköz (American Society of Civil Engineers, 2013)
      The paper presents an attempt to predict the load carrying capacity of perforated rack columns by the direct strength method (DSM). The investigation is focused on two different issues: the prediction of the elastic buckling ...
    • Performance of Steel Moment Connections under a Column Removal Scenario. II: Analysis 

      Fahim; Sadek; Joseph A.; Main; H. S.; Lew; Sherif; El-Tawil (American Society of Civil Engineers, 2013)
      This paper presents a computational investigation of the response of steel beam-column assemblies with moment connections under monotonic loading conditions simulating a column removal scenario. Two beam-column assemblies ...
    • Internet-Enabled Wireless Structural Monitoring Systems: Development and Permanent Deployment at the New Carquinez Suspension Bridge 

      Kurata; Kim; J. P.; Lynch; G. W.; van der Linden; Sedarat; Thometz; Hipley; L.-H.; Sheng (American Society of Civil Engineers, 2013)
      Dense networks of low-cost wireless sensors have the potential to facilitate prolific data collection in large and complex infrastructure at costs lower than those historically associated with tethered counterparts. While ...
    • Analysis of Elastic, Doubly Symmetric, Horizontally Curved Beams during Lifting 

      Raymond H.; Plaut; Cristopher D.; Moen (American Society of Civil Engineers, 2013)
      The lifting of horizontally curved beams (or almost-straight beams with an imperfection in shape) is considered, with application in the construction of bridges. A circularly curved beam that is suspended at two symmetric ...
    • Estimating Natural Periods of Steel Plate Shear Wall Frames 

      Shi; Liu; Gordon P.; Warn; Jeffrey W.; Berman (American Society of Civil Engineers, 2013)
      A steel plate shear wall (SPSW) with thin, unstiffened web plates is one type of seismic lateral force–resisting system that is gaining popularity. SPSWs are used in low to midrise building construction typically with two ...
    • Performance of Advanced Materials during Earthquake Loading Tests of a Bridge System 

      Carlos A.; Cruz Noguez; M. Saiid; Saiidi (American Society of Civil Engineers, 2013)
      Three unconventional details for the plastic hinge regions of bridge columns subjected to seismic loads were developed, designed, and implemented in a large-scale, four-span RC bridge. Superelastic shape memory alloys ...
    • Adaptive Negative Stiffness: New Structural Modification Approach for Seismic Protection 

      D. T. R.; Pasala; A. A.; Sarlis; Nagarajaiah; A. M.; Reinhorn; M. C.; Constantinou; Taylor (American Society of Civil Engineers, 2013)
      Yielding can be emulated in a structural system by adding an adaptive negative stiffness device (NSD) and shifting the yielding away from the main structural system, leading to the new idea of apparent weakening that occurs, ...
    • Reliability Analysis of RC Beams Exposed to Fire 

      Christopher D.; Eamon; Elin; Jensen (American Society of Civil Engineers, 2013)
      A procedure for conducting reliability analysis of RC beams subjected to a fire load is presented. This involves identifying relevant load combinations, specifying critical load and resistance random variables, and ...
    • Comparative Study on Steel Plate Shear Walls Used in a High-Rise Building 

      Jianguo; Nie; Jiansheng; Fan; Xiaogang; Liu; Yuan; Huang (American Society of Civil Engineers, 2013)
      Tianjin Jinta Tower is the first high-rise building built with steel plate shear walls in China. The main lateral force resisting system is the composite core tube composed of steel plate shear walls and concrete-filled ...
    • Structural Behavior of CHS T-Joints Subjected to Brace Axial Compression in Fire Conditions 

      K. H.; Tan; T. C.; Fung; M. P.; Nguyen (American Society of Civil Engineers, 2013)
      The structural behavior of circular hollow section (CHS) T-joints subjected to axial brace compression in fire conditions was investigated. Five full-scale tubular joints with different brace-to-chord diameter ratios were ...
    • Collapse Assessment of Steel Moment Frames Based on E-Defense Full-Scale Shake Table Collapse Tests 

      Dimitrios G.; Lignos; Tsuyoshi; Hikino; Yuichi; Matsuoka; Masayoshi; Nakashima (American Society of Civil Engineers, 2013)
      This paper presents key parameters that affect numerical modeling of steel frame structures for reliable collapse simulations. The collapse assessment is based on experimental data obtained from a full-scale shaking table ...