Browsing Journal of Thermal Science and Engineering Applications by Title
Now showing items 565-584 of 1295
-
Heat and Mass Transfer Analysis in the Stagnation Region of Maxwell Fluid With Chemical Reaction Over a Stretched Surface
(The American Society of Mechanical Engineers (ASME), 2018)A simple model of homogeneous–heterogeneous process for Maxwell fluid flow in stagnation region past a stretched surface is constructed. It is assumed that the homogeneous process in the ambient fluid is governing by ... -
Heat and Mass Transfer Analysis of a Pot in Pot Refrigerator Using Reynolds Flow Model
(The American Society of Mechanical Engineers (ASME), 2016)Heat and mass transfer analysis of evaporative cooling process in a potinpot cooling system is done based on Reynolds flow hypotheses. The model proposed herein assumes that the heat transfer due to natural convection is ... -
Heat and Mass Transfer Caused by a Laminar Channel Flow Equipped With a Synthetic Jet Array
(The American Society of Mechanical Engineers (ASME), 2010)Low Reynolds number laminar channel flow is used in various heat/mass transfer applications such as cooling and mixing. A low Reynolds number implies a low intensity of heat/mass transfer ... -
Heat and Mass Transfer in Planar Anode Supported Solid Oxide Fuel Cells: Effects of Interconnect Fuel/Oxidant Channel Flow Cross Section
(The American Society of Mechanical Engineers (ASME), 2015)Heat and mass transfer in a planar anodesupported solid oxide fuel cell (SOFC) module, with bipolarplate interconnect flow channels of different shapes are computationally simulated. The electrochemistry is modeled by ... -
Heat Characteristics Analysis of Electro-Hydraulic Servo Valve
(The American Society of Mechanical Engineers (ASME), 2019)A new method of building electro-hydraulic servo valve's thermal model is proposed. In this method, energy conservation equation of servo valve was obtained according to thermodynamics, which describes servo valve's heat ... -
Heat Conduction Effect on Oscillating Heat Pipe Operation
(The American Society of Mechanical Engineers (ASME), 2011)The effect of heat conduction through the adiabatic section on the oscillating motion and heat transfer performance in an oscillating heat pipe (OHP) was investigated experimentally. Two, closed ... -
Heat Conduction in a Rectangular Tube With Eccentric Hot Spots
(The American Society of Mechanical Engineers (ASME), 2011)The current paper presents the results of an analytical study of steady state heat conduction in a rectangular tube with eccentric hot spots on both the top and the bottom surfaces. The ... -
Heat Development and Comparison Between the Steady and Pulsating Flows Through Aluminum Foam Heat Sink
(The American Society of Mechanical Engineers (ASME), 2017)Continuous improvements in electronic devices for high-performance computers have led to a need for new and more effective methods of chip cooling. The first purpose of this study was to investigate the heat transfer ... -
Heat Dissipation System Based on Electromagnetic-Driven Rotational Flow of Liquid Metal Coolant
(The American Society of Mechanical Engineers (ASME), 2021)Liquid metal owns the highest thermal conductivity among all the currently available fluid materials. This property enables it to be a powerful coolant for the thermal management of large power device or high flux chip. ... -
Heat Exchanger Design of Direct Evaporative Cooler Based on Outdoor and Indoor Environmental Conditions
(The American Society of Mechanical Engineers (ASME), 2014)Performance of a direct evaporative cooler (DEC) was numerically studied at various outdoor and indoor air conditions, with geometric and physical characteristics of it being extracted based on thermal comfort criteria. ... -
Heat Pipe Thermal Management at Hypersonic Vehicle Leading Edges: A Low-Temperature Model Study
(American Society of Mechanical Engineers (ASME), 2019)The intense thermal fluxes and aero-thermomechanical loads generated at sharp leading edges of atmospheric hypersonic vehicles traveling above Mach 5 have motivated an interest in novel thermal management strategies. Here, ... -
Heat Sink Effect on System Pressure and Mass Flow Rate in a Pumped Refrigerant Loop
(The American Society of Mechanical Engineers (ASME), 2012)Pumped refrigerant loops (PRL) which are aimed at eventually cooling electronics often reject heat to a vapor compression cycle. A vapor compression cycle (VCC) uses a proportional, integral, ... -
Heat Spreader Based on Room-Temperature Liquid Metal
(The American Society of Mechanical Engineers (ASME), 2012)This study reports a high-performance heat spreader based on room-temperature liquid metal coolant. Conceptual cooling experiments show that liquid metal heat spreader owns particularly excellent ... -
Heat Transfer Analysis of a Novel Pressurized Air Receiver for Concentrated Solar Power via Combined Cycles
(The American Society of Mechanical Engineers (ASME), 2009)A novel design of a high-temperature pressurized solar air receiver for power generation via combined Brayton–Rankine cycles is proposed. It consists of an annular reticulate porous ceramic (RPC) ... -
Heat Transfer Analysis of Cu–Water Nanofluid in a District Cooling Chilled Water Loop
(The American Society of Mechanical Engineers (ASME), 2022)Nanofluids consist of nanoparticles made of materials with high thermal conductivity suspended in a base fluid such as water. In theory, the presence of thermally conductive nanoparticles in a base fluid improves the heat ... -
Heat Transfer Analysis of Flash Evaporation With MEPCM
(American Society of Mechanical Engineers (ASME), 2019)Several seawater desalination technologies have been developed and widely used during the last four decades. In the current investigation, a new approach to the seawater desalination process is presented, which utilizes ... -
Heat Transfer Analysis of Slewing Ring Bearing for High Thermal Applications
(The American Society of Mechanical Engineers (ASME), 2017)The challenge in design and manufacturing tasks includes precise measurement of static friction, stiffness, deformation, raceway relative approach, and heat distribution of slewing ring bearings. These parameters affect ... -
Heat Transfer Analysis of the Surface of a Nozzle Guide Vane in a Transonic Annular Cascade
(The American Society of Mechanical Engineers (ASME), 2019)In the current study, a numerical analysis was performed for the heat transfer over the surface of nozzle guide vanes (NGVs) using three-dimensional computational fluid dynamics (CFD) models. The investigation has taken ... -
Heat Transfer and Critical Heat Flux of Subcooled Water Flow Boiling in a SUS304-Tube With Twisted-Tape Insert
(The American Society of Mechanical Engineers (ASME), 2011)The subcooled boiling heat transfer and the steady state critical heat fluxes (CHFs) in a short SUS304-tube with twisted-tape insert are systematically measured for mass velocities (G=4016–13,950 ... -
Heat Transfer and Entropy Generation Analysis of Bingham Plastic Fluids in Circular Microchannels
(The American Society of Mechanical Engineers (ASME), 2015)The thermal characteristics of Bingham plastic fluid flows are analyzed in circular microchannels under uniform wall heat flux condition. The analytic approach presented here reveals that the governing parameters are Bingham ...