Adjacent Level Hypermobility and Instrumented Level Fatigue Loosening With Titanium and PEEK Rods for a Pedicle Screw System: An In Vitro StudySource: Journal of Biomechanical Engineering:;2016:;volume( 138 ):;issue: 005::page 51004Author:Agarwal, Aakas
,
Ingels, Marcel
,
Kodigudla, Manoj
,
Momeni, Narjes
,
Goel, Vijay
,
Agarwal, Anand K.
DOI: 10.1115/1.4032965Publisher: The American Society of Mechanical Engineers (ASME)
Abstract: Adjacentlevel disease is a common iatrogenic complication seen among patients undergoing spinal fusion for low back pain. This is attributed to the postsurgical differences in stiffness between the spinal levels, which result in abnormal forces, stress shielding, and hypermobility at the adjacent levels. In addition, as most patients undergoing these surgeries are osteoporotic, screw loosening at the index level is a complication that commonly accompanies adjacentlevel disease. Recent studies indicate that a rod with lower rigidity than that of titanium may help to overcome these detrimental effects at the adjacent level. The present study was conducted in vitro using 12 L1S1 specimens divided into groups of six, with each group instrumented with either titanium rods or PEEK (polyetheretherketone) rods. The test protocol included subjecting intact specimens to pure moments of 10 Nm in extension and flexion using an FS20 Biomechanical Spine Test System (Applied Test Systems) followed by hybrid moments on the instrumented specimens to achieve the same L1S1 motion as that of the intact specimens. During the protocol's later phase, the L4L5 units from each specimen were segmented for cyclic loading followed by postfatigue kinematic analysis to highlight the differences in motion preand postfatigue. The objectives included the in vitro comparison of (1) the adjacentlevel motion before and after instrumentation with PEEK and titanium rods and (2) the preand postfatigue motion at the instrumented level with PEEK and titanium rods. The results showed that the adjacent levels above the instrumentation caused increased flexion and extension with both PEEK and titanium rods. The postfatigue kinematic data showed that the motion at the instrumented level (L4L5) increased significantly in both flexion and extension compared to prefatigue motion in titanium groups. However, there was no significant difference in motion between the preand postfatigue data in the PEEK group.
|
Collections
Show full item record
| contributor author | Agarwal, Aakas | |
| contributor author | Ingels, Marcel | |
| contributor author | Kodigudla, Manoj | |
| contributor author | Momeni, Narjes | |
| contributor author | Goel, Vijay | |
| contributor author | Agarwal, Anand K. | |
| date accessioned | 2017-05-09T01:26:09Z | |
| date available | 2017-05-09T01:26:09Z | |
| date issued | 2016 | |
| identifier issn | 0148-0731 | |
| identifier other | bio_138_05_051004.pdf | |
| identifier uri | http://yetl.yabesh.ir/yetl/handle/yetl/160402 | |
| description abstract | Adjacentlevel disease is a common iatrogenic complication seen among patients undergoing spinal fusion for low back pain. This is attributed to the postsurgical differences in stiffness between the spinal levels, which result in abnormal forces, stress shielding, and hypermobility at the adjacent levels. In addition, as most patients undergoing these surgeries are osteoporotic, screw loosening at the index level is a complication that commonly accompanies adjacentlevel disease. Recent studies indicate that a rod with lower rigidity than that of titanium may help to overcome these detrimental effects at the adjacent level. The present study was conducted in vitro using 12 L1S1 specimens divided into groups of six, with each group instrumented with either titanium rods or PEEK (polyetheretherketone) rods. The test protocol included subjecting intact specimens to pure moments of 10 Nm in extension and flexion using an FS20 Biomechanical Spine Test System (Applied Test Systems) followed by hybrid moments on the instrumented specimens to achieve the same L1S1 motion as that of the intact specimens. During the protocol's later phase, the L4L5 units from each specimen were segmented for cyclic loading followed by postfatigue kinematic analysis to highlight the differences in motion preand postfatigue. The objectives included the in vitro comparison of (1) the adjacentlevel motion before and after instrumentation with PEEK and titanium rods and (2) the preand postfatigue motion at the instrumented level with PEEK and titanium rods. The results showed that the adjacent levels above the instrumentation caused increased flexion and extension with both PEEK and titanium rods. The postfatigue kinematic data showed that the motion at the instrumented level (L4L5) increased significantly in both flexion and extension compared to prefatigue motion in titanium groups. However, there was no significant difference in motion between the preand postfatigue data in the PEEK group. | |
| publisher | The American Society of Mechanical Engineers (ASME) | |
| title | Adjacent Level Hypermobility and Instrumented Level Fatigue Loosening With Titanium and PEEK Rods for a Pedicle Screw System: An In Vitro Study | |
| type | Journal Paper | |
| journal volume | 138 | |
| journal issue | 5 | |
| journal title | Journal of Biomechanical Engineering | |
| identifier doi | 10.1115/1.4032965 | |
| journal fristpage | 51004 | |
| journal lastpage | 51004 | |
| identifier eissn | 1528-8951 | |
| tree | Journal of Biomechanical Engineering:;2016:;volume( 138 ):;issue: 005 | |
| contenttype | Fulltext |