Journal of Fluids Engineering: Recent submissions
Now showing items 8561-8580 of 9024
-
Discussion: “Influence of Inlet Flow Conditions and Geometries of Centrifugal Vaneless Diffusers on Critical Flow Angle for Reverse Flow” (Senoo, Yasutoshi, and Kinoshita, Yoshifumi, 1977, ASME J. Fluids Eng., 99, pp. 98–102)
(The American Society of Mechanical Engineers (ASME), 1977) -
An Experimental Study of Choked Flow in Short Pipes With Low Air Water Mass Fractions
(The American Society of Mechanical Engineers (ASME), 1977)Using steady flow of air/water at low mass ratios, choking was obtained in short pipes by reducing the back pressure well below atmospheric pressure. Variation of flow parameters affected the ... -
The Particle-Source-In Cell (PSI-CELL) Model for Gas-Droplet Flows
(The American Society of Mechanical Engineers (ASME), 1977)The analysis of gas-droplet flows is complicated by the need to account for the mass, momentum, and energy coupling between phases. The concept of regarding the droplet phase as a source of ... -
Deceleration Rate Parameter and Algebraic Prediction of Turbulent Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1977)The deceleration rate θ1 /λ, which is defined as the ratio of the momentum thickness to the distance where the free-stream velocity is reduced by 10 percent, is shown as an important and ... -
Design of Two-Dimensional Wind Tunnel Contractions
(The American Society of Mechanical Engineers (ASME), 1977)Design charts for 2-D wind tunnel contractions have been developed using inviscid flow analysis, in which a one-parameter family of wall shapes, based on two cubic arcs, was investigated in ... -
Prediction of Flow Separation in a Diffuser by a Boundary Layer Calculation
(The American Society of Mechanical Engineers (ASME), 1977)From a consideration of flow stability, it is shown that the onset of separation in a diffuser depends upon the local blockage factor. Using performance data for two-dimensional diffusers from ... -
Response of Fluid-Elastically Coupled Coaxial Cylindrical Shells to External Flow
(The American Society of Mechanical Engineers (ASME), 1977)The dynamics of a system of two fluid-elastically coupled coaxial cylindrical shells is studied theoretically. The general equations of motion for free and forced-damped vibration are derived in ... -
Pulsatile Blood Flow in a Channel of Small Exponential Divergence—III. Unsteady Flow Separation
(The American Society of Mechanical Engineers (ASME), 1977)Analysis of pulsatile flow through exponentially diverging channels reveals the existence of critical mean Reynolds numbers for which the flow separates at a downstream axial station. These ... -
Deposition of Suspensions in the Entrance of a Channel
(The American Society of Mechanical Engineers (ASME), 1977)An analytical investigation of the mechanics of deposition in a channel from the channel inlet to a distance of 7 channel depths has been made and a mathematical model developed for the ... -
Some Characteristics of High Waves in Closed Channels Approaching Kelvin-Helmholtz Instability
(The American Society of Mechanical Engineers (ASME), 1977)The characteristics of water waves produced by flowing air in closed channels were studied to uncover the effects of surface pressure variation. From theoretical considerations, it is proposed ... -
A Length-Scale Model For Developing Turbulent Flow in a Rectangular Duct
(The American Society of Mechanical Engineers (ASME), 1977)A three-dimensional mixing length model is proposed for modeling local Reynolds stress behavior in rectangular ducts of arbitrary aspect ratio. The model is applicable to both developing and ... -
Discussion: “Experimental Support for Generalized Equation Predicting Low Cycle Fatigue” (Tavernelli, J. F., and Coffin, Jr., L. F., 1962, ASME J. Basic Eng., 84, pp. 533–537)
(The American Society of Mechanical Engineers (ASME), 1962) -
An Initial Approach to the Design of Very Wide Angle Axisymmetric Diffusers With Gauzes to Achieve Uniform Outlet Velocity Profiles
(The American Society of Mechanical Engineers (ASME), 1977)A method is presented of designing very wide angle axisymmetric diffusing ducts which achieve uniform outlet velocity profiles. The aim was to concentrate the major part of the diffuser pressure ... -
Linearized Theory of Supercavitating Hydrofoils in Subsonic Liquid Flow
(The American Society of Mechanical Engineers (ASME), 1977)In order to clarify the compressibility effect, the perturbed flow field of the supercavitating hydrofoil in subsonic region is examined by a linearized technique and, as a result, the general ... -
Discussion: “The Calculation of Turbulent Boundary Layers on Spinning and Curved Surfaces” (Launder, B. E., Priddin, C. H., and Sharma, B. I., 1977, ASME J. Fluids Eng., 99, pp. 237–239)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Review—Progress in Numerical Turbomachinery Analysis” (Japikse, David, 1976, ASME J. Fluids Eng., 98, pp. 592–606)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Quasi-Three-Dimensional Numerical Solution of Flow in Turbomachines” (Bosman, C., and El-Shaarawi, M. A. I., 1977, ASME J. Fluids Eng., 99, pp. 132–140)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “On the Calculation of Three-Dimensional Divergent and Rotational Flow in Turbomachines” (Ribaut, M., 1977, ASME J. Fluids Eng., 99, pp. 187–196)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “On the Stability of Rotors in Cylindrical Journal Bearings” (Rentzepis, G. M., and Sternlicht, B., 1962, ASME J. Basic Eng., 84, pp. 521–531)
(The American Society of Mechanical Engineers (ASME), 1962) -
Truth in Publication
(The American Society of Mechanical Engineers (ASME), 1977)