Journal of Fluids Engineering: Recent submissions
Now showing items 8581-8600 of 9024
-
Discussion: “Design of Two-Dimensional Wind Tunnel Contractions” (Morel, Thomas, 1977, ASME J. Fluids Eng., 99, pp. 371–377)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Deceleration Rate Parameter and Algebraic Prediction of Turbulent Boundary Layer” (Senoo, Y., and Nishi, M., 1977, ASME J. Fluids Eng., 99, pp. 390–394)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Prediction of Flow Separation in a Diffuser by a Boundary Layer Calculation” (Senoo, Y., and Nishi, M., 1977, ASME J. Fluids Eng., 99, pp. 379–386)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Orifice Cavitation and Its Effect on Spray Mixing” (Nurick, W. H., 1976, ASME J. Fluids Eng., 98, pp. 681–687)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Calculated Orifice Plate Discharge Coefficients at Low Reynolds Numbers” (Keith, T. G., and John, James E. A., 1977, ASME J. Fluids Eng., 99, pp. 424–425)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “An Optimum Stepped Piston for Cylinders Working With Compressible Fluid” (Etsion, I., 1976, ASME J. Fluids Eng., 98, pp. 494–498)
(The American Society of Mechanical Engineers (ASME), 1977) -
The Emmons-Mark Debate
(The American Society of Mechanical Engineers (ASME), 1977) -
Prediction of Oscillation Frequencies for Unstable Flow Past Cavities
(The American Society of Mechanical Engineers (ASME), 1977)The incompressible flow of a shear layer past a cavity can undergo relatively large amplitude organized transverse oscillations which arise from hydrodynamic instability. A model which enables ... -
Free Turbulent Shear Layers on Plug Nozzles
(The American Society of Mechanical Engineers (ASME), 1977)Two-dimensional, free, turbulent mixing between a uniform stream and a cavity flow is investigated experimentally in a plug nozzle, a geometry that generates idealized mixing layer conditions. ... -
“IRIS” A Computerized High Head Pump Turbine Design System
(The American Society of Mechanical Engineers (ASME), 1977)“IRIS” is a computerized design and structural optimization system capable of generating all the major hydraulic and mechanical design parameters of high head pump/turbines from limited input ... -
A Free-Streamline Model for Bluff Bodies in Confined Flow
(The American Society of Mechanical Engineers (ASME), 1977)A potential flow model is presented for two-dimensional symmetrical bluff bodies under wall confinement. It provides a procedure for predicting surface loading on a bluff body over a range of ... -
Liquid-Solid Impact Calculations With Triangular Elements
(The American Society of Mechanical Engineers (ASME), 1977) -
Refinement of the Mean Streamline Method of Blade Section Design
(The American Society of Mechanical Engineers (ASME), 1977)The Mean Streamline Method of cascade blade section design developed by Wislicenus correlates the differences in the shape of the blade camber-line and the one-dimensional mean flow streamline. ... -
Direct Measurement of Wall Shear Stress With Mass Transfer in a Low Speed Boundary Layer
(The American Society of Mechanical Engineers (ASME), 1977)A porous plate floating element is used to obtain direct measurements of shear stress in a transpired zero pressure gradient boundary layer from laminar asymptotic suction to blow-off. The ... -
Stability of a Curved Free Streamline
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “The Simulation of Bearing Whirl on an Electronic-Analog Computer” (Jennings, U. D., and Ocvirk, F. W., 1962, ASME J. Basic Eng., 84, pp. 503–508)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “Free Turbulent Shear Layers on Plug Nozzles” (Scott, C. J., and Rask, D. R., 1977, ASME J. Fluids Eng., 99, pp. 301–308)
(The American Society of Mechanical Engineers (ASME), 1977) -
A Note in Comment on “A Reynolds Stress Model for Turbulent Corner Flows”
(The American Society of Mechanical Engineers (ASME), 1977)In [1] Gessner and Emery proposed a closure scheme for the Reynolds-stress equations such that the resultant equations are algebraic and can be solved for the various stress components for ... -
Effect of Upstream Flow Processes on Hydrodynamic Development in a Duct
(The American Society of Mechanical Engineers (ASME), 1977)Consideration is given to the developing laminar flow in a parallel plate channel, with the fluid being drawn from a large upstream space. The flow fields upstream and downstream of the channel ... -
Discussion: “A Preliminary Study of Whirl Instability for Pressurized Gas Bearings” (Larson, R. H., and Richardson, H. H., 1962, ASME J. Basic Eng., 84, pp. 511–518)
(The American Society of Mechanical Engineers (ASME), 1962)