Journal of Fluids Engineering: Recent submissions
Now showing items 8541-8560 of 9024
-
The Time Domain of Centrifugal Compressor and Pump Stability and Surge
(The American Society of Mechanical Engineers (ASME), 1977)New evidence about the time domain operation of centrifugal compressors and pumps in compliant systems is presented. Data from Toyama [1,2] plus unpublished data from another compressor indicate ... -
Discussion: “An Experimental Study of Surge in Centrifugal Compressors” (Toyama, Kosuke, Runstadler, Jr., P. W., and Dean, Jr., R. C., 1977, ASME J. Fluids Eng., 99, pp. 115–124)
(The American Society of Mechanical Engineers (ASME), 1977) -
An Experimental Investigation of the Control of Surge in Radial Compressors Using Close Coupled Resistances
(The American Society of Mechanical Engineers (ASME), 1977)The aerodynamic characteristics of centrifugal compressors are examined with special attention given to the range of flows normally in the unstable region. They are examined for the intended ... -
Discussion: “A Nearly Three-Dimensional Intrablade Computing System for Turbomachinery” (Novak, R. A., and Hearsey, R. M., 1977, ASME J. Fluids Eng., 99, pp. 154–166)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Effects of Extra Sinusoidal Inputs to Nonlinear Systems” (Oldenburger, R., and Boyer, R. C., 1962, ASME J. Basic Eng., 84, pp. 559–569)
(The American Society of Mechanical Engineers (ASME), 1962) -
Estimation of Centrifugal Compressor Stability With Diffuser Loss-Range System
(The American Society of Mechanical Engineers (ASME), 1977)A method has been developed by which centrifugal compressor flow range and the nature of the pressure ratio characteristic approaching surge can be predicted by use of fundamental impeller exit ... -
Discussion: “Reconsideration of the Annulus Flow Problem in Axial Turbomachinery” (Mellor, G. L., 1962, ASME J. Basic Eng., 84, pp. 579–585)
(The American Society of Mechanical Engineers (ASME), 1962) -
Discussion: “The Optimum Response of Full Third-Order Systems With Contactor Control” (Flügge-Lotz, I., and Titus, H. A., 1962, ASME J. Basic Eng., 84, pp. 554–557)
(The American Society of Mechanical Engineers (ASME), 1962) -
Frequency Response of a Tube Bundle in Water
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Asymmetric Flow in Vaneless Diffusers of Centrifugal Blowers” (Senoo, Yasutoshi, Kinoshita, Yoshifumi, and Ishida, Masahiro, 1977, ASME J. Fluids Eng., 99, pp. 104–111)
(The American Society of Mechanical Engineers (ASME), 1977) -
Calculated Orifice Plate Discharge Coefficients at Low Reynolds Numbers
(The American Society of Mechanical Engineers (ASME), 1977) -
Nonaxisymmetric Flow in the Narrow Gap Between a Rotating and a Stationary Disk With an Eccentric Source
(The American Society of Mechanical Engineers (ASME), 1977) -
REVIEW—A Critical Review of Turbomachinery Noise
(The American Society of Mechanical Engineers (ASME), 1977)The review is written from the point of view of an engineer wanting to understand, reduce, and predict noise from turbomachines. In consequence knowledge gained by theory and, in particular, ... -
The Breakup Length of Turbulent Liquid Jets
(The American Society of Mechanical Engineers (ASME), 1977)A formula for the statistical distribution of the breakup length of a turbulent liquid jet is derived. The formula is based on a model in which random turbulent fluctuations are amplified by ... -
Discussion: “The Effect of Rotor Blade Wakes on Centrifugal Compressor Diffuser Performance—A Comparative Experiment” (Baghdadi, Samy, 1977, ASME J. Fluids Eng., 99, pp. 45–50)
(The American Society of Mechanical Engineers (ASME), 1977) -
Conditions for a Pipe to Run Full When Discharging Liquid Into a Space Filled With Gas
(The American Society of Mechanical Engineers (ASME), 1977)Experiments were performed with water discharging into air from horizontal and vertical tubes of several diameters. The horizontal tubes discharged into a variable space between vertical plates. ... -
High-Speed Impact Between Curved Liquid Surface and Rigid Flat Surface
(The American Society of Mechanical Engineers (ASME), 1977)The impact process of a cylindrical, a spherical and a conical water drop upon a rigid plane is studied with numerical methods. Time variation of drop cross-section, pressure and velocity ... -
Discussion: “An Experimental Investigation of the Control of Surge in Radial Compressors Using Close Coupled Resistances” (Dussourd, J. L., Pfannebecker, G. W., and Singhania, S. K., 1977, ASME J. Fluids Eng., 99, pp. 64–74)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “The Time Domain of Centrifugal Compressor and Pump Stability and Surge” (Dean, Jr., R. C., and Young, L. R., 1977, ASME J. Fluids Eng., 99, pp. 53–59)
(The American Society of Mechanical Engineers (ASME), 1977) -
Discussion: “Impeller Stalling as Influenced by Diffusion Limitations” (Rodgers, C., 1977, ASME J. Fluids Eng., 99, pp. 84–93)
(The American Society of Mechanical Engineers (ASME), 1977)