Journal of Fluids Engineering: Recent submissions
Now showing items 2541-2560 of 9024
-
Anisotropy of Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1971)The anisotropy of fatigue crack propagation in hot rolled steel plate was studied for three orientations, viz., crack arrester, crack divider, and short transverse. The dependence of crack growth ... -
A Theoretical Approach to Creep Deformation During Intermittent Load
(The American Society of Mechanical Engineers (ASME), 1971)The influence of intermittent loading on creep deformation has been examined in terms of the recovery creep theory. It has been shown that according to this theory a material exposed to cyclic ... -
Measurements of Mean Flow Velocity Beyond a Rotating Disk
(The American Society of Mechanical Engineers (ASME), 1971)Measurements were made of the mean velocity components of the turbulent flow field just beyond the edge of a thin disk rotating in its own plane. An approximate analysis was made of the ... -
Flow Separation and Reattachment in Confined Jet Mixing
(The American Society of Mechanical Engineers (ASME), 1971)An experimental and theoretical investigation was conducted to study flow separation and reattachment for a confined axisymmetric jet. The fluid was air with an initially uniform velocity jet ... -
An Interferometric Technique for Temperature and Concentration Measurement for an Air-Water Interface
(The American Society of Mechanical Engineers (ASME), 1971)A new technique for the measurement of temperature and concentration for a simultaneous heat and mass transfer analysis is described. The technique employs a one wavelength Mach-Zehnder interferometer ... -
Evaluation of Cardiac Work by Means of the Thermodilution Technique Employing the Thermocatheter
(The American Society of Mechanical Engineers (ASME), 1971)A procedure has been developed for calculating the work performed by the left ventricle during the heartbeat. This procedure involves the continuous direct measurement of fluid mixture temperature ... -
Heat Transfer Characteristics in Air Fluidized Solids up to 900 F
(The American Society of Mechanical Engineers (ASME), 1971)A theory for the mechanism of heat transfer in gas fluidized solids has been developed. Supporting data has been obtained. An empirical equation which fits the theory and correlates the data ... -
Method of Separation of Variables for the Solution of Certain Nonlinear Partial Differential Equations
(The American Society of Mechanical Engineers (ASME), 1971)A method for the solution of a certain class of nonlinear partial differential equations by the method of separation of variables is presented. The method enables the nonlinear partial differential ... -
Analysis and Physiological Monitoring of the Human Left Ventricle
(The American Society of Mechanical Engineers (ASME), 1971)Mathematical models of the human left ventricle are presented to determine the physiological response-oriented mechanical parameters of the LV, which have diagnostic significance. These parameters ... -
Large Deformation Analysis of the Arterial Cross Section
(The American Society of Mechanical Engineers (ASME), 1971)Possible relations between arterial wall stresses and deformations and mechanisms contributing to atherosclerosis are discussed. Necessary material properties are determined experimentally and from ... -
Generalized Expansion Factor of an Orifice for Subsonic and Supercritical Flows
(The American Society of Mechanical Engineers (ASME), 1971)General expressions are developed which approximate the expansion factor of any orifice in any installation for both subsonic and supercritical flows. These factors are based on a presumed ... -
Generalized Contraction Coefficient of an Orifice for Subsonic and Supercritical Flows
(The American Society of Mechanical Engineers (ASME), 1971)After a brief historical review of the pertinent literature, expressions are developed which approximate the compressible contraction coefficient of any orifice in any installation for both subsonic ... -
Formulation of Equations for Orifice Coefficients
(The American Society of Mechanical Engineers (ASME), 1971) -
Erratum: “The Effects of an Annular Fluid on the Vibrations of a Long Rotor, Part I—Theory” (Journal of Basic Engineering, 1970, 92, pp. 923–929)
(The American Society of Mechanical Engineers (ASME), 1971) -
Addendum: “Further Remarks on Similar Solutions for Laminar Boundary Layers” (Journal of Basic Engineering, 1965, 87, pp. 483–494; 1968, 90, pp. 301–312)
(The American Society of Mechanical Engineers (ASME), 1971) -
Closure to “Discussion of ‘The Effect of Some Gaseous Environments on the Creep of a Stainless Steel’” (Le May, I., Truss, K. J., and Sethi, P. S., 1969, ASME J. Basic Eng., 91, pp. 575–580)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “An Axial Compressor End-Wall Boundary Layer Theory” (Mellor, G. L., and Wood, G. M., 1971, ASME J. Basic Eng., 93, pp. 300–314)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Transient Response of Fluid Lines Including Frequency Modulated Inputs” (Kantola, R., 1971, ASME J. Basic Eng., 93, pp. 274–281)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Measurements of Mean Flow Velocity Beyond a Rotating Disk” (Chanaud, R. C., 1971, ASME J. Basic Eng., 93, pp. 199–204)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “An Interferometric Technique for Temperature and Concentration Measurement for an Air-Water Interface” (Prasad, C., Chen, C. S., and Beard, J. T., 1971, ASME J. Basic Eng., 93, pp. 185–190)
(The American Society of Mechanical Engineers (ASME), 1971)