Journal of Fluids Engineering: Recent submissions
Now showing items 2521-2540 of 9024
-
Discussion: “The Response of a Turbulent Boundary Layer to an Upstanding Step Change in Surface Roughness” (Antonia R. A., and Luxton, R. E., 1971, ASME J. Basic Eng., 93, pp. 22–32)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “An Investigation of the Effect of Cavitation Bubbles on the Momentum Loss in Transient Pipe Flow” (Weyler, M. E., Streeter, V. L., and Larsen, P. S., 1971, ASME J. Basic Eng., 93, pp. 1–7)
(The American Society of Mechanical Engineers (ASME), 1971) -
An Optical Study of a Shock Wave Interacting With a Change in Cross Section
(The American Society of Mechanical Engineers (ASME), 1971) -
Design of a Perfectly “Effective” Boiling Fin
(The American Society of Mechanical Engineers (ASME), 1971) -
Stokes Second Problem for the Cylinder
(The American Society of Mechanical Engineers (ASME), 1971) -
Slip Flow in the Entrance of a Parallel Plate Channel
(The American Society of Mechanical Engineers (ASME), 1971) -
Cyclic Plasticity: Some Properties of the Hysteresis Curve of Structural Metals at Room Temperature
(The American Society of Mechanical Engineers (ASME), 1971)The hysteresis curve in the transient and steady-state stage is characterized by inequalities and periodicity conditions for the tangent to the hysteresis curve (dσ/dε) and its derivative (d2 ... -
An Axial Compressor End-Wall Boundary Layer Theory
(The American Society of Mechanical Engineers (ASME), 1971)The essential ingredient missing in existing prediction methods for the performance of multistage axial compressors is that which would account for the effect of end-wall boundary layers. It is, ... -
Low Reynolds Number Turbulent Flow in Large Aspect Ratio Rectangular Ducts
(The American Society of Mechanical Engineers (ASME), 1971)Experiments are reported on fully developed turbulent flows at low Reynolds numbers in rectangular ducts of large aspect ratio. Six ducts, with aspect ratios between 15.5:1 and 35.0:1, were ... -
Shear Strength of Beryllium, Uranium, and Tungsten as a Function of Strain, Strain Rate, and Pressure
(The American Society of Mechanical Engineers (ASME), 1971)The shear strengths of beryllium, uranium, and tungsten were measured at strain rates of 3.5 × 10−5 , 3.6 × 10−3 , and 3.7 × 10−1 sec−1 . The measurements were taken under ... -
A Generalized Static Model for Fluidic Impact Modulators
(The American Society of Mechanical Engineers (ASME), 1971)A static model for predicting the input-output characteristics of direct and transverse impact modulators is presented. The model is based on the position and shape of the dividing streamsurface ... -
Transient Response of Fluid Lines Including Frequency Modulated Inputs
(The American Society of Mechanical Engineers (ASME), 1971)In this paper, analytic descriptions for the step and impulse responses of the fluid in rigid cylindrical lines are obtained in the time domain. In all cases, the fluids considered are Newtonian ... -
Fracture Safety Analysis Concepts for Nuclear Pressure Vessels, Considering the Effects of Irradiation
(The American Society of Mechanical Engineers (ASME), 1971)One of the most important aspects of the growth of nuclear power has been the development and use of quantitative methods of analysis for insuring the reliability of plant components and for ... -
Use of Fracture Mechanics in Reactor Vessel Surveillance
(The American Society of Mechanical Engineers (ASME), 1971)This paper presents the basis for utilizing fracture mechanics technology based upon data obtained from small Charpy V-notch specimens incorporated in reactor vessel surveillance programs. Included ... -
A Reassessment of Fracture-Safe Operating Criteria for Reactor Vessel Steels Based on Charpy-V Performance
(The American Society of Mechanical Engineers (ASME), 1971)Fracture-safe operating criteria for commercial nuclear pressure vessels based on fracture analysis diagram procedures and Charpy-V energy trends are reappraised with respect to the effects of ... -
Determination of Residual Stresses From Stress Intensity Factor Measurements
(The American Society of Mechanical Engineers (ASME), 1971)It is shown that a familiar procedure for obtaining stress intensity factors for a plate containing a through crack may be inverted. That is, stress intensity factor measurements may be used ... -
Holographic Detection of Microcracks
(The American Society of Mechanical Engineers (ASME), 1971)This paper describes the application of optical holographic interferometry to the detection of microcracks in metals. In particular, detection of radial cracks extending from bolt holes in high ... -
Fracture Toughness of ASTM A533 Grade B Class 1 Heavy Section Submerged Arc Weldments
(The American Society of Mechanical Engineers (ASME), 1971)Fracture toughness data are presented for two ASTM A533 Grade B Class 1, 12-in-thick plate submerged arc process weldments. These data were generated in accordance with current ASTM recommended ... -
Embrittlement of Precipitation Hardenable Nickel-Base Alloys by Oxygen
(The American Society of Mechanical Engineers (ASME), 1971)A study was made of the embrittling effects of oxygen on René 41, a nickel-base alloy hardened by precipitation of gamma prime. In short time tensile tests in air it was found that from ... -
Elevated Temperature Properties of Maraging Steel Plates and Welds
(The American Society of Mechanical Engineers (ASME), 1971)The creep rupture behavior, and the effects of elevated temperature exposure in air and hydrogen on the subsequent room temperature properties of a 12 percent Ni-5 percent Cr-3 percent Mo ...