Journal of Fluids Engineering: Recent submissions
Now showing items 2561-2580 of 9024
-
Discussion: “Analysis and Physiological Monitoring of the Human Left Ventricle” (Ghista, D. N., Advani, S. H., Gaonkar, G. H., Balachandran, K., and Brady, A. J., 1971, ASME J. Basic Eng., 93, pp. 147–159)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Large Deformation Analysis of the Arterial Cross Section” (Simon, B. R., Kobayashi, A. S., Strandness, D. E., and Wiederhielm, C. A., 1971, ASME J. Basic Eng., 93, pp. 138–145)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Generalized Expansion Factor of an Orifice for Subsonic and Supercritical Flows” (Benedict, R. P., 1971, ASME J. Basic Eng., 93, pp. 121–136)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Generalized Contraction Coefficient of an Orifice for Subsonic and Supercritical Flows” (Benedict, R. P., 1971, ASME J. Basic Eng., 93, pp. 99–120)
(The American Society of Mechanical Engineers (ASME), 1971) -
Vortex Shedding From Smooth Cylinders and Stranded Cables
(The American Society of Mechanical Engineers (ASME), 1971) -
Heat Transfer in Resonant Cavities Spanned By Low Speed, Turbulent, Shear Layers
(The American Society of Mechanical Engineers (ASME), 1971) -
Fire-Fighting Benefits of Polymeric Friction Reduction
(The American Society of Mechanical Engineers (ASME), 1971) -
Selecting Materials to Resist Low Cycle Fatigue
(The American Society of Mechanical Engineers (ASME), 1971)The selection of materials in the design of components to resist low cycle fatigue is considered in terms of reliable methods of material comparison which can be used in lieu of extensive ... -
Two-Dimensional Miter-Bend Flow
(The American Society of Mechanical Engineers (ASME), 1971)Measurements have been made of the mean flow in a two-dimensional, constant-width, ninety-degree miter bend and compared with predictions of available free-streamline theories. Agreement is quite ... -
The Natural Frequencies of Two Spherical Bubbles Oscillating in Water
(The American Society of Mechanical Engineers (ASME), 1971)The natural frequencies of two spherical bubbles, as they oscillate near each other in water, was theoretically studied, by taking account of surface tension, and on the assumption of the gas ... -
Optimum Vane Number and Angle of Centrifugal Pumps With Logarithmic Vanes
(The American Society of Mechanical Engineers (ASME), 1971)The optimum number of vanes for a given centrifugal pump or blower cannot be estimated by Pfleiderer’s equation because of its limitations. In the present investigation, Stodola’s effect is ... -
Evaluation of Angle to Be Subtended by the Spiral of Semispiral Casings
(The American Society of Mechanical Engineers (ASME), 1971)A hydrodynamic model is considered for estimating the angle to be subtended by the spiral portion of high specific speed axial flow water turbine casings. The results are correlated with the ... -
A Study of Contrarotating Turbines Based on Design Efficiency
(The American Society of Mechanical Engineers (ASME), 1971)In this paper the efficiency of an axial flow contrarotating turbine is expressed in terms of two dimensionless parameters. From this expression the efficiency of a single runner tubular turbine ... -
Flow in Rotating Straight Pipes of Circular Cross Section
(The American Society of Mechanical Engineers (ASME), 1971)The friction factor for fully developed flow in smooth wall straight pipes of circular cross section rotating at a constant angular velocity about an axis perpendicular to its own has been ... -
On the Correlation of Analytical and Experimental Free Shear Layer Similarity Profiles by Spread Rate Parameters
(The American Society of Mechanical Engineers (ASME), 1971)Analysis of turbulent isobaric free jet mixing normally requires the introduction of suitably formulated viscosity models. Similarity solutions can then be established which contain one empirical ... -
Thermal Effects in the Free Oscillation of Gas Bubbles
(The American Society of Mechanical Engineers (ASME), 1971)A theory is developed from first principles which includes all the important physical processes which affect the frequency of the free oscillations of a gas bubble. The components of the ... -
Frequency Response of Fluid Lines With Nonlinear Boundary Conditions
(The American Society of Mechanical Engineers (ASME), 1971)The harmonic distortion generated when a fluid line is terminated by a nonlinear orifice characteristic is analyzed by using a perturbation method of solution. The perturbation method is shown ... -
A Two-Dimensional Analysis of a Heated Free Jet at Low Reynolds Numbers
(The American Society of Mechanical Engineers (ASME), 1971)To spin polymers and glass into continuous fibers, hot molten material is made to flow through a nozzle into air, thus forming a free liquid jet. This cools as it proceeds through the air ... -
Integral Method for Flow Between Corotating Disks
(The American Society of Mechanical Engineers (ASME), 1971)An integral method is developed for the three-dimensional, nonboundary-layer flow which occurs for laminar, radially inward through-flow of an incompressible Newtonian fluid between parallel corotating ... -
Confined Jet Mixing for Nonseparating Conditions
(The American Society of Mechanical Engineers (ASME), 1971)The mixing of an air jet with a lower-velocity air stream is described. The mixing takes place in a constant diameter pipe, and the flow is investigated from the inlet where the jet and ...