Journal of Fluids Engineering: Recent submissions
Now showing items 2581-2600 of 9024
-
Erratum: “Anisotropy of Fatigue Crack Propagation” (Journal of Basic Engineering, 1971, 93, pp. 211–217)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “The Natural Frequencies of Two Spherical Bubbles Oscillating in Water” (Shima, A., 1971, ASME J. Basic Eng., 93, pp. 426–431)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Optimum Vane Number and Angle of Centrifugal Pumps With Logarithmic Vanes” (Reddy, Y. R., and Kar, S., 1971, ASME J. Basic Eng., 93, pp. 411–422)
(The American Society of Mechanical Engineers (ASME), 1971) -
Discussion: “Confined Jet Mixing for Nonseparating Conditions” (Razinsky, E., and Brighton, J. A., 1971, ASME J. Basic Eng., 93, pp. 333–347)
(The American Society of Mechanical Engineers (ASME), 1971) -
Effect of Curvature on the Stability of a Tangential Discontinuity
(The American Society of Mechanical Engineers (ASME), 1971) -
A Method for Determining the Effect of Initial Boundary Layer on Turbulent Free Shear Layer Velocity Profiles
(The American Society of Mechanical Engineers (ASME), 1971) -
The Yield Condition and Flow Rule for a Metal Subjected to Finite Elastic Volume Change
(The American Society of Mechanical Engineers (ASME), 1971)A theory for elastic-plastic deformation with finite elastic strain is outlined. The results of this theory are specialized to consider a metal subjected to high hydrostatic pressure which ... -
Phase Transformation Effects on the Bending Stress Distributions in Carburized Steel Components
(The American Society of Mechanical Engineers (ASME), 1971)An analytical model has been developed for the elastic and elastoplastic bending of rectangular bars in which the neutral bending plane need not remain in the geometric center of the bar. ... -
Bridging the Gap Between Continuum Mechanical Microrotation Viscosity and Lagrangian Point Particles
(The American Society of Mechanical Engineers (ASME), 2013)The microrotation viscosity is an essential fluid property in micropolar fluid dynamics. By considering a dilute suspension of inertial spherical pointparticles in an otherwise Newtonian fluid, an explicit analytical ... -
On Approximating the Translational Velocity of Vortex Rings
(The American Society of Mechanical Engineers (ASME), 2013)A method is presented whereby the translational velocity of a vortex ring can be approximated from the total circulation, impulse, and kinetic energy of the vortex system. Assuming a uniform vorticity density, these bulk ... -
Initiation and Statistical Evolution of Horizontal Slug Flow With a Two Fluid Model
(The American Society of Mechanical Engineers (ASME), 2013)In the present work, the onset and subsequent development of slug flow in horizontal pipes is investigated by solving the transient onedimensional version of the twofluid model in a high resolution mesh using a finite ... -
Instability of a Confined Viscoelastic Liquid Sheet in a Viscous Gas Medium
(The American Society of Mechanical Engineers (ASME), 2013)A linear analysis method was used to investigate the instability behavior of a viscoelastic liquid sheet moving through a viscous gas bounded by two horizontal parallel flat plates. The liquid sheet velocity profile was ... -
Molecular Tagging Velocimetry and Its Application to In Cylinder Flow Measurements
(The American Society of Mechanical Engineers (ASME), 2013)This review article provides an overview of the experimental studies of incylinder flows using various flow measurement techniques with a focus on molecular tagging velocimetry. It is necessary to understand the evolution ... -
Identification of Critical Net Positive Suction Head From Noise and Vibration in a Radial Flow Pump for Different Leading Edge Profiles of the Vane
(The American Society of Mechanical Engineers (ASME), 2013)Experimental investigations concerning cavitation in radial flow pump for three different leading edge profiles of the vane were carried out in an open circuit system. The operating condition of the radial flow pump under ... -
A Lattice Boltzmann Simulation of Three Dimensional Displacement Flow of Two Immiscible Liquids in a Square Duct
(The American Society of Mechanical Engineers (ASME), 2013)A threedimensional (3D), multiphase lattice Boltzmann approach is used to study a pressuredriven displacement flow of two immiscible liquids of different densities and viscosities in a square duct. A threedimensional, ... -
A Nonlinear Computational Model of Floating Wind Turbines
(The American Society of Mechanical Engineers (ASME), 2013)The dynamic motion of floating wind turbines is studied using numerical simulations. The full threedimensional Navier–Stokes equations are solved on a regular structured grid using a level set method for the free surface ... -
Flow and Heat Transfer of Powell–Eyring Fluid Over a Stretching Surface: A Lie Group Analysis
(The American Society of Mechanical Engineers (ASME), 2013)In this study, the flow and heat transfer of Powell–Eyring fluid over a permeable stretching surface is examined. By using Lie group analysis, the symmetries of the equations are found. Four finite parameter and one ... -
Experimental Investigation of Microscale Effects in Perforated Plate Aerodynamics
(The American Society of Mechanical Engineers (ASME), 2013)This paper contains an extensive analysis of the flow in microholes based on an experimental investigation. Experiments of the gas flow past a perforated plate with microholes (110خ¼m) were carried out. A wide range of ... -
Optimal Perturbations in Boundary Layer Flows Over Rough Surfaces
(The American Society of Mechanical Engineers (ASME), 2013)This work provides a threedimensional energy optimization analysis, looking for perturbations inducing the largest energy growth at a finite time in a boundarylayer flow in the presence of roughness elements. The immersed ... -
Cumulative Fatigue Damage Under Stress-Controlled Conditions
(The American Society of Mechanical Engineers (ASME), 1971)A theoretical analysis of uniaxial cumulative fatigue damage is presented together with a large number of experimental results on unnotched specimens of A-201 and A-517 steels. The theory developed ...