Journal of Fluids Engineering: Recent submissions
Now showing items 1661-1680 of 9024
-
Discussion: “Turbulence Structure for Fully Developed Flow in Rough Pipes” (Powe, R. E., and Townes, H. W., 1973, ASME J. Fluids Eng., 95, pp. 255–260)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Effect of an Oscillating Free Stream on the Unsteady Pressure on a Circular Cylinder” (Hatfield, H. M., and Morkovin, M. V., 1973, ASME J. Fluids Eng., 95, pp. 249–252)
(The American Society of Mechanical Engineers (ASME), 1973) -
Gas-Tracer Method of Steady and Pulsating-Flow Measurement
(The American Society of Mechanical Engineers (ASME), 1961)A method is described of measuring the bulk mass-flow rate in steady and pulsating air streams with the aid of a suitable tracer gas such as carbon dioxide. The method briefly involves ... -
Discussion: “The Calibration Correlation Function for Positive Displacement Liquid Meters” (Keyser, D. R., 1973, ASME J. Fluids Eng., 95, pp. 180–188)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Analysis of Unsteady Laminar Boundary Layer Flow by an Integral Method” (Miller, R. W., and Han, L. S., 1973, ASME J. Fluids Eng., 95, pp. 237–247)
(The American Society of Mechanical Engineers (ASME), 1973) -
A Dynamic Modeling Method of Unsteady Flows in Long Fluid Lines With Turbulent Bulk Velocities
(The American Society of Mechanical Engineers (ASME), 1973)An analytical method is presented to solve the equations of unsteady gas flow in a long tube with turbulent bulk-flow velocity. The nonlinearity of the equations is overcome by judicious choice ... -
Turbulent Mixing in the Developing Region of Coaxial Jets
(The American Society of Mechanical Engineers (ASME), 1973)Measurements of mean velocity, the three normal stresses and Reynolds shear stress are reported in the developing region of coaxial jet flows. The measurements were obtained with three velocity ... -
On the Generalization of the Mangler Transformation for Axisymmetric Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1973) -
Flow Measurement for Accounting Purposes
(The American Society of Mechanical Engineers (ASME), 1961)This paper discusses the industrial measurement of gases and liquids by means of thin-plate orifices. Installation and maintenance practices which reduce measurement errors are described. Records ... -
Vortex Shedding From Slender Cylinders of Various Cross Sections
(The American Society of Mechanical Engineers (ASME), 1973)Vortex shedding frequencies were measured for a number of cylinders of various geometrical shapes by placing a hot-wire sensor in the near wake and autocorrelating the turbulence signal. Strouhal ... -
A Finite Difference Solution of the Two and Three-Dimensional Incompressible Turbulent Boundary Layer Equations
(The American Society of Mechanical Engineers (ASME), 1973)A modified Crank-Nicholson implicit finite difference formulation is presented for two and three-dimensional turbulent boundary layers. The turbulent stresses are treated after Prandtl’s early mixing ... -
Discussion: “Air and Water Studies on a Diffuser-Modified Flow Nozzle” (Benedict, R. P., Gleed, A. R., and Schulte, R. D., 1973, ASME J. Fluids Eng., 95, pp. 169–177)
(The American Society of Mechanical Engineers (ASME), 1973) -
Shallow Creeping Flow Round a Corner Under Gravity
(The American Society of Mechanical Engineers (ASME), 1973) -
Oscillatory Flow Phenomena in Diffusers at Low Reynolds Numbers
(The American Society of Mechanical Engineers (ASME), 1973)In studies of a diffuser operating with inlet flow oscillations, it has been found that large amplification of the inlet velocity oscillations occurs within the diffuser when the throat Reynolds ... -
Expansion Coefficients for Orifice Meters in Pipes Less Than One Inch in Diameter
(The American Society of Mechanical Engineers (ASME), 1961)A practical technique for using orifices to meter most gases of engineering interest is described. This technique can be employed in pipes less than 1 in. ID, as well as in larger sizes. ... -
Performance of Low-Aspect-Ratio Diffusers With Fully Developed Turbulent Inlet Flows: Part II—Development and Application of a Performance Prediction Method
(The American Society of Mechanical Engineers (ASME), 1973)An analytical method of the integral type is developed to allow prediction of performance in unstalled, straight, two-dimensional rectangular diffusers of aspect ratio less than approximately 0.5. ... -
An Assessment of Three-Dimensional Turbulent Boundary Layer Prediction Methods
(The American Society of Mechanical Engineers (ASME), 1973)Predictions have been made for a variety of experimental three-dimensional boundary layer flows with a single finite difference method which was used with three different turbulent stress models: ... -
Time-Dependent Pipe Forces Caused by Blowdown and Flow Stoppage
(The American Society of Mechanical Engineers (ASME), 1973)Formulations are developed in this study for rapid estimates of time-and-space-dependent pipe reaction forces caused by either sudden blowdown or flow stoppage in a fluid piping system. The ... -
An Investigation of Pressure Transients in a System Containing a Liquid Capable of Air Absorption
(The American Society of Mechanical Engineers (ASME), 1973)The object of the paper is to describe the formulation and use of a computer model which will predict the mode of flow in hydraulic systems with rapidly changing boundary conditions. The ... -
Performance of Low-Aspect-Ratio Diffusers With Fully Developed Turbulent Inlet Flows: Part I—Some Experimental Results
(The American Society of Mechanical Engineers (ASME), 1973)An experimental investigation of the effects of incompressible, fully developed, turbulent inlet flow on the performance of straight, two-dimensional rectangular diffusers of low aspect ratio is ...