Journal of Fluids Engineering: Recent submissions
Now showing items 1641-1660 of 9024
-
Analysis of Unsteady Laminar Boundary Layer Flow by an Integral Method
(The American Society of Mechanical Engineers (ASME), 1973)An approximate integral method of analysis is developed for unsteady laminar boundary layer flows. The case of a flat plate in a free stream with small harmonic velocity oscillations about a ... -
A Note on the Calculation of Supercavitating Hydrofoils With Rounded Noses
(The American Society of Mechanical Engineers (ASME), 1973)Practical supercavitating hydrofoils have rounded leading edges for mechanical strength. The prediction of pressures near the leading edge of such hydrofoils by linearized free-streamline theory ... -
The Suppression of Shear Layer Turbulence in Rotating Systems
(The American Society of Mechanical Engineers (ASME), 1973)Stabilization of turbulent boundary layer type flows by the action of Coriolis forces engendered by system rotation is studied. Experiments on fully developed, two-dimensional flow in a long, ... -
A Counter-Rotating Pair of Turbulent Jets
(The American Society of Mechanical Engineers (ASME), 1973)A study has been made of a pair of swirling jets having opposite rotation. Mean flow and turbulent intensity measurements were obtained and characteristics of the spreading rate determined. The ... -
The Calibration Correlation Function for Positive Displacement Liquid Meters
(The American Society of Mechanical Engineers (ASME), 1973)This paper presents a correlation function for the disk type of positive displacement oil meters. This correlation will predict the shift in the calibration curve due to differences in fluid ... -
Application of Linearized Friction Impedance Models to Complex Fluid Systems
(The American Society of Mechanical Engineers (ASME), 1973)Results of correlating system frequency response test data with analytic data are presented. The test data are from four complex systems, incorporating series and parallel piping configurations ... -
Calculation of Interacting Turbulent Shear Layers: Duct Flow
(The American Society of Mechanical Engineers (ASME), 1973)The boundary-layer calculation method of Bradshaw, Ferriss, and Atwell has been adapted to deal with the interaction between two shear layers with a change of sign of shear stress. Good agreement ... -
Discussion: “Hydrodynamic Phenomena During High-Speed Collision Between Liquid Droplet and Rigid Plane” (Huang, Yen C., Hammitt, F. G., and Yang, W-J, 1973, ASME J. Fluids Eng., 95, pp. 276–292)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Measurement of Two-Dimensional Periodic Flow With a Cobra Probe” (Senoo, Y., Kita, Y., and Ookuma, K., 1973, ASME J. Fluids Eng., 95, pp. 295–299)
(The American Society of Mechanical Engineers (ASME), 1973) -
Oil Flow in a Full Journal Bearing
(The American Society of Mechanical Engineers (ASME), 1961)An analysis was made of the oil flows occurring in a full journal bearing with a continuous oil film. The flow rate into the bearing was determined at the section of greatest clearance and ... -
Discussion: “Eddy-Viscosity Distribution in Thick Axisymmetric Turbulent Boundary Layers” (Cebeci, T., 1973, ASME J. Fluids Eng., 95, pp. 319–324)
(The American Society of Mechanical Engineers (ASME), 1973) -
Air and Water Studies on a Diffuser-Modified Flow Nozzle
(The American Society of Mechanical Engineers (ASME), 1973)The effect of adding a separable diffuser to a conventional flow nozzle is studied, analytically and experimentally, concerning the flow discharge coefficient and the loss characteristic of the ... -
Discussion: “Status of Fluid Transients in Western Europe and the United Kingdom. Report on Laboratory Visits by Freeman Scholar” (Martin, C. S., 1973, ASME J. Fluids Eng., 95, pp. 301–311)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “The Measurement and Effects of Edge Sharpness on the Flow Coefficients of Standard Orifices” (Crockett, K. A., and Upp, E. L., 1973, ASME J. Fluids Eng., 95, pp. 271–274)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Some Considerations of Material Response Due to Liquid-Solid Impact” (Peterson, F. B., 1973, ASME J. Fluids Eng., 95, pp. 263–270)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Effect of Pressure on the Length of Cavity and Cavitation Damage Behind Circular Cylinders in a Venturi” (Chandrasekhara, D. V., and Syamala Rao, B. C., 1973, ASME J. Fluids Eng., 95, pp. 197–205)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Calculation of Interacting Turbulent Shear Layers: Duct Flow” (Bradshaw, P., Dean, R. B., and McEligot, D. M., 1973, ASME J. Fluids Eng., 95, pp. 214–219)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “The Suppression of Shear Layer Turbulence in Rotating Systems” (Johnston, J. P., 1973, ASME J. Fluids Eng., 95, pp. 229–235)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “A Counter-Rotating Pair of Turbulent Jets” (Pratte, B. D., and Keffer, J. F., 1973, ASME J. Fluids Eng., 95, pp. 207–213)
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “A Note on the Calculation of Supercavitating Hydrofoils With Rounded Noses” (Furuya, O., and Acosta, A. J., 1973, ASME J. Fluids Eng., 95, pp. 221–227)
(The American Society of Mechanical Engineers (ASME), 1973)