Journal of Fluids Engineering: Recent submissions
Now showing items 1681-1700 of 9024
-
An Approximate Method for the Solution of a Class of Nonlinear Equations in Fluid Mechanics and Magnetohydrodynamics
(The American Society of Mechanical Engineers (ASME), 1973)An approximate method has been developed to obtain a closed form solution of a class of nonlinear two-point boundary value problems. Application of this method to three problems in Fluid ... -
The Use of Subgrid Transport Equations in a Three-Dimensional Model of Atmospheric Turbulence
(The American Society of Mechanical Engineers (ASME), 1973)A three-dimensional numerical model of turbulence in an atmospheric boundary layer has been revised to utilize subgrid transport equations for the subgrid Reynolds stresses and fluxes rather than ... -
An Initial Value Method for the Study of Shock-Induced Laminar Compressible Boundary Layers
(The American Society of Mechanical Engineers (ASME), 1973)An initial value method is applied for investigating laminar compressible boundary layers created by the passage of a plane shock wave over an infinite flat plate. The two point boundary value ... -
Instability in the Vortex Street Wakes of Vibrating Bluff Bodies
(The American Society of Mechanical Engineers (ASME), 1973) -
Mean Temperature and Velocity in a Plane Turbulent Jet
(The American Society of Mechanical Engineers (ASME), 1973) -
Further Data on the Pressure Recovery Performance of Straight-Channel, Plane-Divergence Diffusers at High Subsonic Mach Numbers
(The American Society of Mechanical Engineers (ASME), 1973)Measurements are reported of the pressure recovery of straight-channel, symmetric, single-plane-divergence diffusers with inlet Mach numbers between 0.2 and choking for an aspect ratio of 5.0. The ... -
Pressure Distributions in Porous Ducts of Arbitrary Cross Section
(The American Society of Mechanical Engineers (ASME), 1973)A general analytical method has been developed to approximate the pressure distribution along a porous duct of an arbitrary cross section with uniform fluid extraction or addition through the ... -
Effects of Curvature on Two-Dimensional Diffuser Flow
(The American Society of Mechanical Engineers (ASME), 1973)The effects of curvature on diffusers have been studied experimentally and analytically. Measurements of wall pressures and boundary layer velocities have been made in three test diffusers of ... -
On the Free Shear Layer Downstream of a Backstep in Supersonic Flow
(The American Society of Mechanical Engineers (ASME), 1973)The free shear layer downstream of a backstep immersed in a supersonic stream is analyzed. The effects of the initial boundary layer and the expansion at the step corner are taken into ... -
A Note on the Critical Pressure Ratio Across a Fluid Meter
(The American Society of Mechanical Engineers (ASME), 1973)The concept of critical static pressure ratio across a fluid meter is first discussed. Various formulations for critical pressure ratios are then developed and solutions are tabulated for ... -
Viscous Effects in the Inception of Cavitation on Axisymmetric Bodies
(The American Society of Mechanical Engineers (ASME), 1973)Cavitation inception and development on two axisymmetric bodies was studied with the aid of a Schlieren flow visualization method developed for that purpose. Both bodies were found to exhibit ... -
Turbulent Jets in a Confined Crossflow
(The American Society of Mechanical Engineers (ASME), 1973)An experimental and analytical study of the deflection and impingement of turbulent jets in a confined crossflow, a geometry which occurs in gas turbine blade impingement cooling schemes, is ... -
The Dynamic Behavior and Compliance of a Stream of Cavitating Bubbles
(The American Society of Mechanical Engineers (ASME), 1973)The role played by turbopump cavitation in the POGO instability of liquid rockets motivates the present study on the dynamic response of streams of cavitating bubbles to imposed pressure ... -
Performance Characteristics of an 8-In-Dia ASME Nozzle Operating at Compressible and Incompressible Conditions
(The American Society of Mechanical Engineers (ASME), 1973)Experimental and theoretical values of local velocity and density were determined at several axial planes within the cylindrical throat region of a standard ASME, long radius, low beta ratio ... -
Three-Dimensional Flow Field in Rocket Pump Inducers—Part 1: Measured Flow Field Inside the Rotating Blade Passage and at the Exit
(The American Society of Mechanical Engineers (ASME), 1973)The measurement of the flow field within the rotating passages as well as three-dimensional characteristics of the exit flow of an inducer model is reported in this paper. The flow within the ... -
Turbulent Viscosities for Swirling Flow in a Stationary Annulus
(The American Society of Mechanical Engineers (ASME), 1973)Developing axial and decaying tangential velocity fields are surveyed in a stationary annulus with a nearly free vortex initial swirl distribution. Isothermal air was used as the working fluid ... -
An Upper Bound on the Stress in Plane Couette Flow
(The American Society of Mechanical Engineers (ASME), 1973)An absolute upper bound on the momentum number in turbulent plane Couette flow is obtained proportional to the two-thirds power of the Reynolds number. The derivation is based upon the energy ... -
Experimental Investigation of Corners in the Yield Surface
(The American Society of Mechanical Engineers (ASME), 1961)The results of fourteen combined stress tests with variable stress ratios on annealed commercially pure aluminum are reported. These tests were made on a combined tension-torsion testing machine ... -
Alan Hugh Stenning, 1928–1973
(The American Society of Mechanical Engineers (ASME), 1973) -
Working Mechanism of Suction Ring and Effects of Its Geometry
(The American Society of Mechanical Engineers (ASME), 1973)The working mechanism of a suction ring and the mechanism in which a geometry of suction ring controls flow patterns inside a turbomachine and the performance of the turbomachine are clarified ...