Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5621-5640 of 7723
-
High-Frequency Fatigue of Metals and Their Cavitation-Damage Resistance
(The American Society of Mechanical Engineers (ASME), 1966)In order to verify the strain-rate effects on the correlation between strain energy of metals and their cavitation-damage resistance, high-frequency fatigue tests at 14.2 kcs were conducted using ... -
Impact on the Surface of a Compressible Fluid
(The American Society of Mechanical Engineers (ASME), 1966)The pressure field generated by the impact of a rigid or flexible body on the surface of an inviscid, compressible fluid is considered. Some general results for the forces generated by the ... -
The Effect of Structural Damping on the Forced Vibrations of Cylindrical Sandwich Shells
(The American Society of Mechanical Engineers (ASME), 1966)This paper presents an examination of the effects of structural damping on the axisymmetric vibrations of a cylindrical sandwich shell. It is shown that the use of core materials with high ... -
An Analytical Study of the Dynamics of an Elastic Linkage
(The American Society of Mechanical Engineers (ASME), 1966)The transverse vibrational characteristics of the connecting rod in a slider-crank mechanism are investigated. The equations of motion are derived, simplified, and solved. For the solution, two ... -
The Study of Spatial Mechanisms by Electronic Analog Computer
(The American Society of Mechanical Engineers (ASME), 1966)A simulation technique, applicable to any spatial mechanism having lower pairs, is presented. A detailed description of the required electronic analog-computer circuitry is given. The geometrical ... -
Acceleration Analysis of Spatial Four-Link Mechanisms
(The American Society of Mechanical Engineers (ASME), 1966)Acceleration analysis of a spatial four-link mechanism with one revolute pair and three cylindrical pairs of general proportions is presented here; results are expressed in concise algebraic forms ... -
On the Lateral Stability and Control of the Automobile as Influenced by the Dynamics of the Steering System
(The American Society of Mechanical Engineers (ASME), 1966)Measurements of the directional response of an automobile to torque inputs applied at the steering wheel are compared with predictions yielded by a five-degree-of-freedom model of a four-wheeled, ... -
A Modified Gibbs Experiment
(The American Society of Mechanical Engineers (ASME), 1966)Experiments were conducted on the effects of the shift of the gas mass from the high-pressure to the low-pressure sides of a divided vessel, with communication by (a) bursting diaphragm and ... -
Flueric Operation on Pressure Signals
(The American Society of Mechanical Engineers (ASME), 1966)A three-stage, jet-deflection-type, proportional fluid amplifier with feedback is used to demonstrate some mathematical and control operations. The operations performed on pressure signals are ... -
Four-Parameter Generalized Compressibility Charts for Nonpolar Fluids
(The American Society of Mechanical Engineers (ASME), 1966)A series of five generalized compressibility charts for nonpolar and slightly polar substances in the gaseous and liquid states and in the two-phase region is presented. The charts are plots ... -
Design Requirements for MC-331 Vehicles
(The American Society of Mechanical Engineers (ASME), 1966)Hauling compressed gases on the highways has been a phenomenon of the post-World War II era. The original requirements of the late 1940’s for interstate shipments were embodied in ICC specification ... -
Computer-Designed Vacuum Vessels
(The American Society of Mechanical Engineers (ASME), 1966)Today a wide variety of chemical and petrochemical processes require equipment that operates under partial vacuum. The ASME Code for Unfired Pressure Vessels, Section VIII, sets forth a method ... -
The Plastic Bending of Beams Considering Die Friction Effects
(The American Society of Mechanical Engineers (ASME), 1966)This paper describes a theoretical and experimental analysis of the behavior of simple beams bent by a central load while freely supported at each end. Both plane strain and plane stress ... -
Discussion: “The Use of Flow-Corrective Inserts in Bins” (Johanson, Jerry R., 1966, ASME J. Eng. Ind., 88, pp. 224–230)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “The Effect of Structural Damping on the Forced Vibrations of Cylindrical Sandwich Shells” (Jones, I. W., and Salerno, V. L., 1966, ASME J. Eng. Ind., 88, pp. 318–323)
(The American Society of Mechanical Engineers (ASME), 1966) -
Dynamic Stability Design of Stacks and Towers
(The American Society of Mechanical Engineers (ASME), 1966)A method is outlined for determining the critical wind velocity, natural frequency, and approximate maximum amplitude of vibration of tall heater stacks and process towers caused by vortex ... -
Discussion: “On the Lateral Stability and Control of the Automobile as Influenced by the Dynamics of the Steering System” (Segel, Leonard, 1966, ASME J. Eng. Ind., 88, pp. 283–294)
(The American Society of Mechanical Engineers (ASME), 1966) -
Electrochemical Machining—Prediction and Correlation of Process Variables
(The American Society of Mechanical Engineers (ASME), 1966)The relationship between total current, applied potential, electrolyte flow rate, electrolyte conductivity, and electrode gap in electrochemical machining was investigated experimentally and analytically. ... -
Ultrasonic Grinding Economics
(The American Society of Mechanical Engineers (ASME), 1966)In ultrasonic grinding the abrasive gradually loses its effectiveness, and must be replaced after a given period of use (T). The rate of material removal (Q in mm3 /min) is related to the ... -
The Effect of Anisotropy and Work-Hardening Characteristics on the Stress and Strain Distribution in Deep Drawing
(The American Society of Mechanical Engineers (ASME), 1966)In the process of the deep drawing of a cup, anisotropy and work-hardening characteristics of the material were introduced, by use of the incremental strain theory, into the calculation of ...