Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5601-5620 of 7723
-
Stress Concentrations in Thin Spherical Shells
(The American Society of Mechanical Engineers (ASME), 1966)Stress distributions occurring in the proximity of rigid circular inserts attached to thin spherical shells are reported in this paper. The solutions are achieved by employing conical coordinates ... -
The Use of Flow-Corrective Inserts in Bins
(The American Society of Mechanical Engineers (ASME), 1966)A properly designed bin and hopper results in savings through better flow-rate control, larger live-storage capacity, and improved uniformity of withdrawn materials. Unfortunately, most bins are ... -
Balancing of Flexible Rotors Having Arbitrary Mass and Stiffness Distribution
(The American Society of Mechanical Engineers (ASME), 1966)A method for balancing a flexible rotor is developed which is based upon the dynamic response of the rotor in its normal modes as excited by the distributed mass unbalance. The balance ... -
Effects of Standoff Tolerances on the Fatigue Life of a Tool-Joint Pin
(The American Society of Mechanical Engineers (ASME), 1966)A 4 1/2 -in. API full-hole, tool-joint pin is stress-analyzed photoelastically over a range of standoffs. A three-dimensional plastic model is loaded to different values of makeup torque. At ... -
Vibration Analysis of Large High-Speed Rotating Equipment
(The American Society of Mechanical Engineers (ASME), 1966)This paper discusses the application of mobility methods to the lateral vibration analysis of coupled machinery. Some effects of bearing and/or casing structural mobility on the rotational system ... -
Predicting the Stability of Long Vertical Pipe Transmitting Torque in a Viscous Medium
(The American Society of Mechanical Engineers (ASME), 1966)This paper presents stability data for a very long vertical pipe transmitting torque in a viscous medium. In addition to these factors, distributed pipe weight and hydrostatic-fluid pressure ... -
Finned Elliptical Tubes and Their Application in Air-Cooled Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1966)Finned circular tubes have been used exclusively in air-cooled heat exchangers built for the American petroleum and chemical industries. In Europe, however, other tube geometries, in particular, ... -
Analysis of Radially Deformed Perforated Flanges
(The American Society of Mechanical Engineers (ASME), 1966)Results of a theoretical and experimental investigation of stresses in radially deformed perforated flanges are presented. The theoretical analysis considers the plane-stress problem of an annular ... -
Analysis of Pressure Pulsations in Reciprocating Compressor Piping Systems
(The American Society of Mechanical Engineers (ASME), 1966)This paper deals with pulsations in pressure and flow in the reciprocating compressor and connected piping system. A model is presented that describes the excitation at the compressor and the ... -
Theoretical and Experimental Band Saw Vibrations
(The American Society of Mechanical Engineers (ASME), 1966)The frequencies of particular, periodic band-saw, transverse-vibration solutions, denoted here as natural frequencies, are determined both theoretically and experimentally. Three simple, approximate ... -
Measurement of the Stresses Set Up in a Resin Bonded Diamond Grinding Wheel While Grinding Harmet G6 Tungsten Carbide
(The American Society of Mechanical Engineers (ASME), 1966)This report describes the work which has been done in measuring stresses developed during diamond grinding, and summarizes the preliminary phases of this investigation. The technical problems ... -
Dimensional Changes in Tube Swaging
(The American Society of Mechanical Engineers (ASME), 1966)The purpose of this study was to investigate changes in the wall thickness of tubes sunk by the rotary swaging process. The independent variables were: Workpiece material, original wall thickness ... -
A Plasticity Problem Involving Plane Strain and Plane Stress Simultaneously: Groove Formation in the Machining of High-Temperature Alloys
(The American Society of Mechanical Engineers (ASME), 1966)Although a plane strain plastic analysis represents a good approximation for the central portion of a metal-cutting chip, plane stress better approximates conditions at the free edges of the ... -
Discussion: “Passive-Element Analog Circuits for Three-Dimensional Elasticity” (Barnoski, R. L., and Freberg, C. R., 1966, ASME J. Eng. Ind., 88, pp. 8–16)
(The American Society of Mechanical Engineers (ASME), 1966) -
Radioisotope Power-Generating System for a Manned Space Laboratory
(The American Society of Mechanical Engineers (ASME), 1966)The results of a Douglas sponsored study of radioisotope secondary power-generating systems for space applications are presented. The study results are applicable to various space vehicles and ... -
Discussion: “Effects of Standoff Tolerances on the Fatigue Life of a Tool-Joint Pin” (Finke, Jr., John, 1966, ASME J. Eng. Ind., 88, pp. 211–215)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Vibration Analysis of Large High-Speed Rotating Equipment” (Ludwig, G. A., 1966, ASME J. Eng. Ind., 88, pp. 201–208)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Predicting the Stability of Long Vertical Pipe Transmitting Torque in a Viscous Medium” (Huang, Tseng, and Dareing, D. W., 1966, ASME J. Eng. Ind., 88, pp. 191–199)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Analysis of Radially Deformed Perforated Flanges” (Kraus, H., Rotondo, P., and Haddon, W. D., 1966, ASME J. Eng. Ind., 88, pp. 172–176)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Analysis of Pressure Pulsations in Reciprocating Compressor Piping Systems” (Grover, S. S., 1966, ASME J. Eng. Ind., 88, pp. 164–168)
(The American Society of Mechanical Engineers (ASME), 1966)