Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5581-5600 of 7723
-
Discussion: “Finned Elliptical Tubes and Their Application in Air-Cooled Heat Exchangers” (Schulenberg, Franz J., 1966, ASME J. Eng. Ind., 88, pp. 179–186)
(The American Society of Mechanical Engineers (ASME), 1966) -
Cryogenic Temperature Dependence of the Yield Strength of High-Strength Alloys
(The American Society of Mechanical Engineers (ASME), 1966)The effect of cryogenic temperatures (from 78 F to −423 F) on the yield strength of twenty alloys was studied. Experimental results prove that they do not conform to any of the following ... -
Effect of Water Immersion on Reduction of Die Stresses in Explosive Forming
(The American Society of Mechanical Engineers (ASME), 1966)This investigation considers the dynamic response of a thin, elastic spherical shell surrounded by a large body of fluid. The blast pressure is applied to the internal shell surface, and three ... -
Sheet Metal Forming Research in Japan
(The American Society of Mechanical Engineers (ASME), 1966)Research activities and their results on sheet metal forming in Japan are introduced with emphasis on the mechanics of sheet metal press-forming. Based on the governing deformation mechanisms ... -
The Thermal Mechanics of Tool Wear
(The American Society of Mechanical Engineers (ASME), 1966)Empirical evidence is presented to show that the geometry of tool wear, and the presence of built-up-edge, is strongly controlled by the chip curl. Evidence is also given which shows that ... -
An Exploratory Study of Taylor’s Tool-Life Equation by Power Transformations
(The American Society of Mechanical Engineers (ASME), 1966)Transformations of both dependent and independent variables are employed to investigate the linearization of Taylor’s tool-life equation. This exploratory study indicates that a logarithmic ... -
On the Mechanics of the Grinding Process Under Plunge Cut Conditions
(The American Society of Mechanical Engineers (ASME), 1966)Two broad categories of grinding action are recognized; one where negligible ploughing and rubbing take place and where the plunge velocity versus normal force intensity curve is a straight ... -
Modern Metals Machining Technology
(The American Society of Mechanical Engineers (ASME), 1966)Titanium alloys such as A-110AT, B-120VCA, C-120AV, and 6-6-2AVT, which have been used to manufacture structural components for the aerospace industry, are difficult to machine when compared to ... -
On the Vibrations of Parabolic Membranes
(The American Society of Mechanical Engineers (ASME), 1966)This study is concerned with the transverse vibrations of a theoretical membrane which occupies a region bounded by two confocal parabolas. The eigenvalues and eigenfunctions for Dirichlet ... -
A Study of the Normal and Shear Stresses on a Cutting Tool
(The American Society of Mechanical Engineers (ASME), 1966)This paper contains an explanation for the variation of the “coefficient of friction” in metal cutting. The chip partly sticks to and partly slides over the tool and only in the latter region ... -
Force and Moment Response of Pneumatic Tires to Lateral Motion Inputs
(The American Society of Mechanical Engineers (ASME), 1966)Equations of motion applicable to a “running-band” model of the pneumatic tire, as developed by von Schlippe, are transformed to the frequency domain, and side-force and aligning-moment responses ... -
Nonlinear Bending of a Stress Corrosion Specimen
(The American Society of Mechanical Engineers (ASME), 1966)This paper presents an analysis of the postbuckling behavior of an initially straight plate strip of variable flexural rigidity whose ends are subjected to opposing “axial” loads. Bending action ... -
Quasi-Steady Flow and Thrust in Accelerating Nozzles and Channels
(The American Society of Mechanical Engineers (ASME), 1966)Internal flows of compressible fluids in nozzles and constant-area channels subjected to constant axial acceleration or gravitation are examined in detail. It is found that the effect of nozzle ... -
Some Effects of Geometry, Orientation, and Acceleration on Pool Film Boiling of Organic Fluids
(The American Society of Mechanical Engineers (ASME), 1966)Ethanol, pentane, and Freon-113 were tested for atmospheric pressure, saturated film-boiling characteristics. Turbulent waves arise close to the bottom of vertical platinum plates and the data ... -
Passive-Element Analog Circuits for Three-Dimensional Elasticity
(The American Society of Mechanical Engineers (ASME), 1966)This paper considers the derivation of passive-element electrical analogs for three-dimensional elasticity in rectangular, cylindrical, and spherical polar coordinates. The analogs represent, in ... -
Discussion: “Effect of Water Immersion on Reduction of Die Stresses in Explosive Forming” (Reismann, H., and Jurney, W. H., 1966, ASME J. Eng. Ind., 88, pp. 111–115)
(The American Society of Mechanical Engineers (ASME), 1966) -
Basic Theory of Rapid-Transit Tunnel Ventilation
(The American Society of Mechanical Engineers (ASME), 1966)An analysis has been carried out for the basic mechanism of rapid-transit tunnel ventilation due to train piston action and for the temperatures resulting in the system. Theory is in general ... -
Discussion: “An Exploratory Study of Taylor’s Tool-Life Equation by Power Transformations” (Wu, S. M., Ermer, D. S., and Hill, W. J., 1966, ASME J. Eng. Ind., 88, pp. 81–89)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “On the Mechanics of the Grinding Process Under Plunge Cut Conditions” (Hahn, R. S., 1966, ASME J. Eng. Ind., 88, pp. 72–79)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “A Study of the Normal and Shear Stresses on a Cutting Tool” (Hsu, T. C., 1966, ASME J. Eng. Ind., 88, pp. 51–61)
(The American Society of Mechanical Engineers (ASME), 1966)