Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 5641-5660 of 7723
-
Maximum Profit as the Criterion in the Determination of the Optimum Cutting Conditions
(The American Society of Mechanical Engineers (ASME), 1966)Maximum profit is an appropriate criterion for the selection of the optimum machining conditions rather than the conventional criteria of minimum cost or maximum production rate. A simple example ... -
An Empirical Equation for the Strain-Rate Effect on Roll Separating Force in Cold Rolling
(The American Society of Mechanical Engineers (ASME), 1966)While decreases in roll separating force with increasing speeds in cold rolling have been noted in many instances, their recording has been primarily qualitative. In order to proceed eventually ... -
The Coefficient of Friction in Cold Rolling
(The American Society of Mechanical Engineers (ASME), 1966)A derivation of a formula for computing the coefficient of friction in the cold rolling process is presented. A simplified model of the pressure distribution in the arc of contact is assumed. ... -
Flow Characteristics Through Conical Converging Dies
(The American Society of Mechanical Engineers (ASME), 1966)A velocity field is considered to describe flow through conical dies. The expected distorted grid pattern is studied. Strain and strain rate fields are analyzed. Effective strain and effective ... -
Effects of Nonsymmetry in Strip Rolling on Single-Roll Drive Mills
(The American Society of Mechanical Engineers (ASME), 1966)An investigation of unsymmetrical deformation effects in hot strip rolling on single-roll drive mills is performed analytically. The model developed permits prediction of the rolling load, torque, ... -
The Mechanism of Material Removal in the Erosive Cutting of Brittle Materials
(The American Society of Mechanical Engineers (ASME), 1966)An analysis is presented for the erosive cutting of a brittle material by the normal impact of a stream of solid particles. The volume of material removed by a given number of particles is ... -
On the Ductile Behavior of Nominally Brittle Materials During Erosive Cutting
(The American Society of Mechanical Engineers (ASME), 1966)It is known that nominally brittle materials may exhibit plastic deformation in indentation, scratching, and microcutting when the loaded region is sufficiently small. The present investigation ... -
Mechanics of Punching Circular Holes in Materials for Data Handling
(The American Society of Mechanical Engineers (ASME), 1966)A theoretical model is developed in an effort to predict the effect of various design and operating parameters on the mechanics of punching circular holes in relatively ductile, nonmetallic ... -
Estimation of Dynamic Forces in Very High-Speed Impact Forging
(The American Society of Mechanical Engineers (ASME), 1966)A study is made of three methods of estimating die loads in impact forging: By approximate solution of the equations of equilibrium; by an energy method, assuming plane sections remain plane; ... -
The Strength of Diamond
(The American Society of Mechanical Engineers (ASME), 1966)Practical, handbook-type information on the strength of diamond is scarce and scattered. This paper reports data taken on the breaking strength of good quality, natural diamond octahedra. Average ... -
Structural Analysis of an Arteriole by the Direct Stiffness Method
(The American Society of Mechanical Engineers (ASME), 1966)The direct stiffness method is used to analyze the structural response of the cross section of an arteriole which is both heterogeneous and nonlinear in terms of structural response. A typical ... -
A Computer Program for Determining the Effect of Design Variation on Service Stresses in Railroad Wheels
(The American Society of Mechanical Engineers (ASME), 1966)Two computer analyses have been prepared relating service stresses in railroad wheels to wheel shape and dimensions. One program computes the temperature distribution and stresses due to heat ... -
The Reciprocal Theorem for Harmonic Oscillations of an Elastic, Isotropic Medium
(The American Society of Mechanical Engineers (ASME), 1966)Using the formulation of continuum mechanics, a dynamic reciprocal theorem is derived for sinusoidal motion of an elastic medium. It is found that, exactly as in the static case, the work of ... -
Discussion: “Dynamic Stability Design of Stacks and Towers” (DeGhetto, Kenneth, and Long, William, 1966, ASME J. Eng. Ind., 88, pp. 462–466)
(The American Society of Mechanical Engineers (ASME), 1966) -
Report of Committee RR-6 Survey: Progress in Railway Mechanical Engineering, 1964–1965
(The American Society of Mechanical Engineers (ASME), 1966)This paper contains the annual report of the ASME Survey Committee RR-6. Developments in Railway Mechanical Engineering from September 1, 1964, to September 1, 1965, which pertain to railcars ... -
Discussion: “Flow Characteristics Through Conical Converging Dies” (Avitzur, B., 1966, ASME J. Eng. Ind., 88, pp. 410–419)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “Effects of Nonsymmetry in Strip Rolling on Single-Roll Drive Mills” (Holbrook, Richard L., and Zorowski, Carl F., 1966, ASME J. Eng. Ind., 88, pp. 401–408)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “The Mechanism of Material Removal in the Erosive Cutting of Brittle Materials” (Sheldon, G. L., and Finnie, I., 1966, ASME J. Eng. Ind., 88, pp. 393–399)
(The American Society of Mechanical Engineers (ASME), 1966) -
Discussion: “A Computer Program for Determining the Effect of Design Variation on Service Stresses in Railroad Wheels” (Riegel, Malcolm S., Levy, Samuel, and Sliter, John A., 1966, ASME J. Eng. Ind., 88, pp. 352–357)
(The American Society of Mechanical Engineers (ASME), 1966) -
On-Line Tool Breakage Detection in Turning: A Multi-Sensor Method
(The American Society of Mechanical Engineers (ASME), 1994)