Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1941-1960 of 7723
-
Discussion: “Stresses in a Pipe Bent Into a Circular Arc” (Weil, N. A., Brock, J. E., and Cooper, W. E., 1961, ASME J. Eng. Ind., 83, pp. 449–455)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Deflection of Heat Exchanger Flanged Joints as Affected by Barreling and Warping” (Dudley, W. M., 1961, ASME J. Eng. Ind., 83, pp. 460–465)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Free Oscillations of Edge-Connected Simply Supported Plate Systems” (Ungar, Eric E., 1961, ASME J. Eng. Ind., 83, pp. 434–439)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Damping Structural Resonances Using Viscoelastic Shear-Damping Mechanisms: Parts I and II” (Ruzicka, Jerome E., 1961, ASME J. Eng. Ind., 83, pp. 403–443 and pp. 414–424)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Balancing Flexible Rotors” (Church, A. H., and Plunkett, R., 1961, ASME J. Eng. Ind., 83, pp. 383–388)
(The American Society of Mechanical Engineers (ASME), 1961) -
The Relative Angular Velocity Between Links
(The American Society of Mechanical Engineers (ASME), 1973)The magnitude of the relative angular velocity between two links is equal to the component of the relative velocity between any two points, one on each link, along the line joining them ... -
Optimal Design of a Regenerative Clutch-Brake
(The American Society of Mechanical Engineers (ASME), 1973)Simplified analytical techniques are developed for the optimal design of a regenerative clutch-brake. The analysis yields parametric equations for the clutch-brake geometry such that wear and ... -
Karman Vortex Streets and Flow-Induced Vibrations in Tube Banks
(The American Society of Mechanical Engineers (ASME), 1973) -
Discussion: “Optimal Design of a Regenerative Clutch-Brake” (Geis, D. G., and Uzgiris, S. C., 1973, ASME J. Eng. Ind., 95, pp. 391–398)
(The American Society of Mechanical Engineers (ASME), 1973) -
Industrial Use of Renovated Municipal Wastewater
(The American Society of Mechanical Engineers (ASME), 1973)A survey of industries in the United States revealed that twenty-two plants are presently using renovated municipal wastewater. Eleven industries have discontinued the usage, one because of the ... -
A Power Cycle to Eliminate Thermal Pollution
(The American Society of Mechanical Engineers (ASME), 1973)A cycle is proposed in which no condenser cooling water is required. Turbine back-pressure is kept to conventional levels by condensing the steam during the evaporation of a refrigerant. Heat ... -
On the Limits to Energy Release and Implications for Present Policy
(The American Society of Mechanical Engineers (ASME), 1973)Technology has been a provider of benefits directly improving man’s lot. These benefits have usually gone first to those already at the top of society, but increased production has gradually ... -
Analytical Sensitivity Studies of the Optimum Machining Conditions for Milling, Drilling, Reaming, and Tapping
(The American Society of Mechanical Engineers (ASME), 1973)An analytical method for sensitivity studies in the determination of the optimum machining conditions for the single point turning process was previously presented by Ermer and Faria [4]. In ... -
Technology and the Limits to Growth
(The American Society of Mechanical Engineers (ASME), 1973)Simulation studies performed over the past two years by a team of scientists at the Massachusetts Institute of Technology indicate that there, are physical limits to the growth of population ... -
Optimization of Drag Minimums Including Effects of Flow Separation
(The American Society of Mechanical Engineers (ASME), 1973)Recent work on the supersonic freestream-centered propulsive jet interaction problem has shown that minimum total afterbody drag can be achieved during power on flight with less than a full ... -
A Finite Element Based Procedure for Simulating the Transient Response and Failure of a Two-Dimensional Continuum With Nonlinear Material Characteristics
(The American Society of Mechanical Engineers (ASME), 1973)This paper presents a finite element based procedure for the analysis and graphic display of the response and failure patterns of a two-dimensional continuum subjected to impulsive loading. ... -
Pressure Ratio Effects on Rarefied Flow Through Square Tubes
(The American Society of Mechanical Engineers (ASME), 1973)Experimental data are presented for the flow of argon gas through a 0.0985 in. sq tube 12 in. long. Data were obtained for pressure ratios varying between 0.943 and 0.0027. The range of ... -
Analysis of Temperature Field in Chip
(The American Society of Mechanical Engineers (ASME), 1973)A solution is presented for the temperature field in the chip under experimental edge conditions in the contact zone and at the upper chip face. The pattern of the temperature gradient in ... -
Computer-Aided Synthesis of Mechanisms Using Nonlinear Programming
(The American Society of Mechanical Engineers (ASME), 1973)The synthesis of spatial mechanisms is formulated as a mathematical programming problem and solved using a penalty function approach. The objective function as well as the equality and inequality ... -
Base Flow Characteristics of a Linear Aerospike Nozzle Segment
(The American Society of Mechanical Engineers (ASME), 1973)The separated base flow region within a linear aerospike nozzle segment is investigated experimentally in an ejector-diffuser system. The nozzle-diffuser system and base pressure characteristics ...