Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1961-1980 of 7723
-
Mesh Generation—A Survey
(The American Society of Mechanical Engineers (ASME), 1973)This report discusses pertinent schemes in finite element mesh generation. It is divided into two parts; node point generation and element generation. Node generation consists of automatically ... -
Investigation of Pulse Tube Refrigerator
(The American Society of Mechanical Engineers (ASME), 1973)This paper reports a theoretical analysis and experimental investigation of pulse tube refrigerator. A concept of steps is introduced for the derivation of cold end temperature with zero heat ... -
An Approximate Rigid-Plastic Analysis of Shell Intersections Loaded Dynamically
(The American Society of Mechanical Engineers (ASME), 1973)An approximate rigid-plastic method of analysis which may be used in order to estimate the behavior of various shell intersections subjected to large dynamic loads is presented herein. In ... -
Radial Displacements of a Hollow Shaft Subjected to a Uniform Band of External Pressure
(The American Society of Mechanical Engineers (ASME), 1973)The principle of superposition is used to combine the results of separate stiffness analyses of (a) a solid shaft loaded by a band of external pressure, using classical elasticity methods and ... -
Review of Materials Processing Literature—1969–1970: 2—Grinding
(The American Society of Mechanical Engineers (ASME), 1973) -
An Improved Technique for Theoretically Determining the Lift Distribution on an Automobile
(The American Society of Mechanical Engineers (ASME), 1973)A technique for determining aerodynamic lift characteristics and surface lift distributions of automobiles is derived. Calculations using both this technique, which includes certain second-order ... -
Diamond Bit Drilling Research
(The American Society of Mechanical Engineers (ASME), 1973)Fundamental relationships of the parameters; penetration rate, bit weight, rotary speed, bit horsepowers, flow rate, and pressure were developed using eight full-scale, oilfield diamond drilling ... -
Design Charts for the Three-Gear Drive
(The American Society of Mechanical Engineers (ASME), 1973)As an intermittent motion mechanism the three-gear drive offers several easily obtained motion characteristics. The design regions in which these characteristics are found are defined by particular ... -
A Means of Increasing Drill Collar Connection Life
(The American Society of Mechanical Engineers (ASME), 1973)Drill collar connection failures have increased as oil and gas wells are drilled to greater depths requiring the use of smaller collars. The high cost resulting from these failures prompted a ... -
Analysis of Center to Edge Foundation Settlement of Atmospheric Storage Tanks
(The American Society of Mechanical Engineers (ASME), 1973)Modern large capacity atmospheric steel storage tanks incur differential settlement of the soil foundations upon which they rest due to the Boussinesq effect [1, 2]. The difference in settlement ... -
Calculation of Residual Stresses in Plastic Deformation Processes
(The American Society of Mechanical Engineers (ASME), 1973)Three problems, namely, autofrettage process, plastic upsetting of a solid cylinder, and plane-strain and axisymmetric extrusion, are treated for residual stress calculation. A thick-walled cylinder ... -
Motion of a Ball in a Ball Bearing
(The American Society of Mechanical Engineers (ASME), 1973)A method is developed which allows the digital simulation of the unsteady motion of a single ball constrained only by two moving bearing races. Any desired motion of the races can be simulated. ... -
Review of Materials Processing Literature—1969–1970: 1—Plastic Working of Metals
(The American Society of Mechanical Engineers (ASME), 1973)The purpose of this review is to apprise the important contributions to the knowledge of materials processing appearing in the published literature and to present a digest of this new knowledge ... -
Review of Materials Processing Literature—1969–1970: 3—Review of German Language Literature
(The American Society of Mechanical Engineers (ASME), 1973) -
A Rotating Valve for High Pressures
(The American Society of Mechanical Engineers (ASME), 1973)Some operations of tumbling barrel type mixers require that the vessel be isolated during treatment of the charge. The present paper describes a valve designed and constructed for such a ... -
Fracture Resistance of Wire-Wrapped Cylinders
(The American Society of Mechanical Engineers (ASME), 1973)Steel cylinders wrapped with steel wire have the capability of offering not only an economical high-strength structure, but also a structure with improved fracture resistance compared with that ... -
Stress State Around an Elliptic Hole in a Conical Shell Under Tension
(The American Society of Mechanical Engineers (ASME), 1973)Membrane stress state around an elliptic hole in a conical shell under tension is determined by perturbation in terms of a nondimensional cone angle ε and a nondimensional curvature parameter ... -
Process Application and Design of Large Power Output Turboexpanders
(The American Society of Mechanical Engineers (ASME), 1973)The design parameters of turboexpanders and their influence on process optimization are reviewed with particular emphasis on hydrocarbon recovery processes requiring large power output turboexpanders. ... -
Rigid-Plastic Collapse of Cylindrical Shells
(The American Society of Mechanical Engineers (ASME), 1973)This paper suggests a simple numerical approach to the limit analysis of cantilever cylindrical shells. The loads considered are external pressure and external pressure combined with a moment ... -
An Evaluation of the Mechanical Properties of Mn-Mo and Mn-Mo-Ni Steels
(The American Society of Mechanical Engineers (ASME), 1973)A study of the effects of normalizing and austenitizing on the mechanical properties of Mn-Mo and Mn-Mo-Ni steels is presented. It is shown that the quenched and tempered condition has superior ...