Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1921-1940 of 7723
-
Deflection of Heat Exchanger Flanged Joints as Affected by Barreling and Warping
(The American Society of Mechanical Engineers (ASME), 1961)The conventional formulas for bolted-flange design, given in the ASME Unfired Pressure Vessel Code, provide for stresses due to initial bolt tightening and the axial force of internal pressure. ... -
Stresses in a Pipe Bent Into a Circular Arc
(The American Society of Mechanical Engineers (ASME), 1961)The stress distribution in circular bends formed from straight pipe and subjected to internal pressure is presented. The analysis determines first the thickness distribution after forming, followed ... -
The Yielded Compound Cylinder in Generalized Plane Strain
(The American Society of Mechanical Engineers (ASME), 1961)The theory of a previous paper [1], which was designed for plane strain of a compound cylinder, is extended to generalized plane strain, where the axial strain is a constant nonzero value ... -
Magnetic Properties of Malleable Irons
(The American Society of Mechanical Engineers (ASME), 1961)Standard or ferritic malleable iron is satisfactory for use as a cast, soft magnetic material. It is made by heat-treating white iron. In addition to its magnetic properties, it can be readily ... -
Free Oscillations of Edge-Connected Simply Supported Plate Systems
(The American Society of Mechanical Engineers (ASME), 1961)A simple semigraphical method for calculating the natural frequencies of two-plate systems is developed, a two-plate system being one made up of two rectangular plates simply supported at all ... -
Damping Structural Resonances Using Viscoelastic Shear-Damping Mechanisms: Part II—Experimental Results
(The American Society of Mechanical Engineers (ASME), 1961)This paper describes the experimental dynamic response characteristics of structural design configurations employing viscoelastic shear-damping mechanisms that have been discussed in a previous paper. ... -
Damping Structural Resonances Using Viscoelastic Shear-Damping Mechanisms: Part I—Design Configurations
(The American Society of Mechanical Engineers (ASME), 1961)This paper considers the problem of resonant vibration control in designing structures to function in modern dynamic environments. Methods of specifying structural damping are given and damping ... -
The Flexural Vibrations of Thin Laminated Cylinders
(The American Society of Mechanical Engineers (ASME), 1961)A method is developed for calculating the natural frequencies of vibration of a thin right circular cylinder. The vibration pattern may contain any number of peripheral or axial nodes. The ... -
Stress and Strain in Spinning Paraboloid Dishes—2
(The American Society of Mechanical Engineers (ASME), 1961)Solutions for the stress and strain systems in spinning paraboloid dishes, both holed and whole, are presented. They are applicable to all such dishes of aperture small enough to justify the ... -
Balancing Flexible Rotors
(The American Society of Mechanical Engineers (ASME), 1961)A method is presented for computing the size and angular location of the correction weights required in selected planes of rotation to balance a flexible shaft rotating at high speeds. It is ... -
Critical Speeds of Two Bearing Machines With Overhung Weight
(The American Society of Mechanical Engineers (ASME), 1961)The purpose of this study was to determine the general frequency expression for a rotating shaft with uniformly distributed weight, supported by two bearings, and carrying a concentrated weight ... -
A Tabular Collocation Method for Beam Vibration
(The American Society of Mechanical Engineers (ASME), 1961)This paper presents a procedure, based on the integral equation method, for the calculation of the natural frequencies of lateral vibration of beams with variable cross section. The approximate ... -
Discussion: “Performances of Carbide Tools in Machining 18-8 Stainless Steel” (Takeyama, H., 1961, ASME J. Eng. Ind., 83, pp. 572–578)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “New Development in the Theory of the Metal-Cutting Process: Part II—The Theory of Chip Formation” (Albrecht, P., 1961, ASME J. Eng. Ind., 83, pp. 557–568)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “An Analysis of the Mechanism of Orthogonal Cutting and Its Application to Discontinuous Chip Formation” (Okushima, Keiji, and Hitomi, Katsundo, 1961, ASME J. Eng. Ind., 83, pp. 545–555)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Fundamental Machinability Research in Japan” (Hitomi, Katsundo, 1961, ASME J. Eng. Ind., 83, pp. 531–542)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Forces on a Worn Cutting Tool” (McAdams, H. T., and Rosenthal, Paul, 1961, ASME J. Eng. Ind., 83, pp. 505–509)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “An Experimental Investigation of Temperature Distribution at Tool-Flank Surface” (Chao, B. T., Li, H. L., and Trigger, K. J., 1961, ASME J. Eng. Ind., 83, pp. 496–503)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “A Theory of Shear Spinning of Cones” (Kobayashi, S., Hall, I. K., and Thomsen, E. G., 1961, ASME J. Eng. Ind., 83, pp. 485–494)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “A Study of Shear-Spinnability of Metals” (Kalpakcioglu, Serope, 1961, ASME J. Eng. Ind., 83, pp. 478–483)
(The American Society of Mechanical Engineers (ASME), 1961)