Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1901-1920 of 7723
-
Discussion: “Practices in Operational Management—Engineering Management” (Paules, C. E., 1961, ASME J. Eng. Ind., 83, pp. 303–306)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Practices in Operational Management—The Management of Industrial Research” (Work, Harold K., 1961, ASME J. Eng. Ind., 83, pp. 297–300)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Practices in General Management—Measurements and Control” (Rathe, A. W., 1961, ASME J. Eng. Ind., 83, pp. 292–296)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Practices in General Management—Financial” (Curry, R. B., 1961, ASME J. Eng. Ind., 83, pp. 287–290)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Management as a Profession” (Smiddy, Harold F., 1961, ASME J. Eng. Ind., 83, pp. 261–276)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Practices in General Management—New Directions for Organizational Practice” (Muller-Thym, B. J., 1961, ASME J. Eng. Ind., 83, pp. 278–286)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Philosophy of Management” (Lederer, A. M., 1961, ASME J. Eng. Ind., 83, pp. 255–258)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Management’s Past—A Guide to Its Future” (Gilbreth, L. M., and Jaffe, W. J., 1961, ASME J. Eng. Ind., 83, pp. 237–247)
(The American Society of Mechanical Engineers (ASME), 1961) -
Milling Forces Measured With a Planetary-Gear Torquemeter
(The American Society of Mechanical Engineers (ASME), 1961)Cutting-force data, obtained with a torquemeter of planetary-gear design in carbide milling tests on SAE-1018 cold-rolled steel at feeds from 0.002 to 0.030 in. per tooth, cutting speeds from ... -
Performances of Carbide Tools in Machining 18-8 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1961)The austenitic 18-8 stainless steel is one of the most troublesome materials to be machined because of the tendencies of work-hardening, high temperature, and adhesion. The ultimate object of ... -
New Development in the Theory of the Metal-Cutting Process: Part II—The Theory of Chip Formation
(The American Society of Mechanical Engineers (ASME), 1961)Introduction of the concept of ploughing into the metal-cutting process lead to the abandoning of the assumption of collinearity of the resultant force on tool face and on the shear plane. ... -
An Analysis of the Mechanism of Orthogonal Cutting and Its Application to Discontinuous Chip Formation
(The American Society of Mechanical Engineers (ASME), 1961)Instead of the conventional theory of the mechanics of metal cutting based on a process of shear confined to a single shear plane, the concept of flow region, a fairly large transitional ... -
Fundamental Machinability Research in Japan
(The American Society of Mechanical Engineers (ASME), 1961)This manuscript presents a brief description of fundamental research in Japan in the field of machinability. -
On the Mechanics of Wire Drawing
(The American Society of Mechanical Engineers (ASME), 1961)Split-die technique was adopted to find the coefficient of friction in wire drawing directly from experiment. Simple dynamometers with wire resistance strain gages were used for measuring separating ... -
Some Controlled Metal-Cutting Studies With Resulfurized Steels
(The American Society of Mechanical Engineers (ASME), 1961)Cutting tests, including controlled tool-chip contact area and controlled artificial flank wear-land studies, were made with five resulfurized steels having nearly identical strength properties. It ... -
Forces on a Worn Cutting Tool
(The American Society of Mechanical Engineers (ASME), 1961)The forces on a single-point cutting tool under conditions of progressive flank wear are analyzed under the assumptions of constant rake, friction, and shear angle. Relations between wear land ... -
An Experimental Investigation of Temperature Distribution at Tool-Flank Surface
(The American Society of Mechanical Engineers (ASME), 1961)The measurement of temperature distribution at the flank surface of a cutting tool is characterized by the extremely small extent of the surface over which the temperature field is explored. ... -
A Theory of Shear Spinning of Cones
(The American Society of Mechanical Engineers (ASME), 1961)The theoretical deformation mechanism of shear spinning of cones was re-evalued. It was found that the predicted tangential or power spinning forces for commercially pure aluminum and lead for ... -
A Study of Shear-Spinnability of Metals
(The American Society of Mechanical Engineers (ASME), 1961)The deformation zone in shear-spinning is idealized for a two-dimensional process and maximum permissible thickness reduction without fracture is predicted in terms of the stress system in this ... -
Thermal-Stress Analysis of Irregular Shapes
(The American Society of Mechanical Engineers (ASME), 1961)A method has been developed for determining the thermal stresses resulting from an axially symmetric temperature distribution in an irregularly shaped cylindrical vessel. It permits the calculation ...