Journal of Manufacturing Science and Engineering: Recent submissions

Now showing items 1641-1660 of 7723

    • Machinability of Nodular Cast Irons: Part I—Tool Forces and Flank Adhesion 

      I. Ham; K. Hitomi; G. L. Thuering (The American Society of Mechanical Engineers (ASME), 1961)
      Three grades of nodular cast iron (60, 80, and 100) were tested to determine the cutting and feed forces required to machine the materials, to determine the performance of several grades of ...

    • On the Analysis of Random Errors in Precision Grinding Operations 

      Robert S. Hahn (The American Society of Mechanical Engineers (ASME), 1961)
      The concept of random variables as used in the theory of probability is applied to machining operations, in which the input stock, hardness, stock distributions, etc., vary. Output errors are ...

    • On the Mechanics of Shear Spinning 

      Serope Kalpakcioglu (The American Society of Mechanical Engineers (ASME), 1961)
      With the use of an idealized model of the shear spinning process some of the basic quantities in the shearing mechanism have been defined and formulated, these being: shear strain, shear ...

    • A New Test Method for Determination of Spinnability of Metals 

      Richard L. Kegg (The American Society of Mechanical Engineers (ASME), 1961)
      A new test method is described whereby the spinnability, i.e., the ability to undergo shear spinning deformation, without fracture, of any material may be determined. Work done to date with ...

    • On Predicting the Dynamic Effects of Clearances in One-Dimensional Closed Loop Systems 

      S. Dubowsky (The American Society of Mechanical Engineers (ASME), 1974)
      The dynamic response of a complex one-dimensional system with clearances is considered. It is shown that the presence of the clearances results in a substantial amplification of the internal ...

    • Axial Deflection Rate of Springs Formed by Transverse Slotting of Thin Wall Cylinders 

      F. R. Archibald (The American Society of Mechanical Engineers (ASME), 1974)

    • Dynamic Characteristics of Rotating and Nonrotating Machine Tool Spindles 

      R. J. Allemang; H. Thomas Graef; C. D. Powell (The American Society of Mechanical Engineers (ASME), 1974)
      The initial concern of this paper is to establish the general relationships between vibration testing using a static machine tool, and vibration testing using a machine tool under dynamic ...

    • The Effect of Geometrical Parameters of Hypoid and Spiroid Gears on Its Quality Characteristics 

      F. L. Litvin; K. M. Petrov; V. A. Ganshin (The American Society of Mechanical Engineers (ASME), 1974)
      The orthogonal hypoid and spiroid gears are considered. The point of tangency of the pitch cones is presumed to be simultaneously the calculation contact point of the teeth surfaces. Analytical ...

    • Engineering in Resuscitation 

      Benjamin Smilg (The American Society of Mechanical Engineers (ASME), 1961)
      The processes of respiration are analyzed from an engineering point of view and the requirements for resuscitator design are outlined. A review of pertinent engineering considerations is presented. ...

    • A Note on Rolling 

      G. A. Fazekas (The American Society of Mechanical Engineers (ASME), 1974)

    • Dynamic Response of Surface-Moored Vertical Barrier to Wave Action by Analog and Digital Simulation 

      J. R. Fowler; E. I. Bailey (The American Society of Mechanical Engineers (ASME), 1974)
      The two-dimensional dynamics of an oil containment barrier, which was designed to have very low tensile loads due to current and waves, were simulated with a theoretical model. The model was ...

    • Application of Constrained-Layer Damping to Control Noise in Machine Parts 

      P. D. Emerson (The American Society of Mechanical Engineers (ASME), 1974)
      A layer of visco-elastic material bonded between surfaces of a vibrating structure and a constraining layer produces appreciable damping of vibration. Application of the technique to textile ...

    • An Experimental Investigation of the Dynamic Response of an Elastic Mechanism 

      R. M. Alexander; K. L. Lawrence (The American Society of Mechanical Engineers (ASME), 1974)
      Interest in the dynamic response of elastic mechanisms has recently prompted several analytical investigations. To date however, experimental data on the response of such mechanisms has been ...

    • Design of Energy Absorbing Upper Torso Restraint Systems 

      E. I. E. Ofodile; J. W. Hannell (The American Society of Mechanical Engineers (ASME), 1974)
      Based on current DOT requirements for a car occupant restraint in car crashes, the load-extension characteristics for an upper torso belt system capable of safety restraining an average motorist ...

    • On the Doubly Regenerative Stability of a Grinder 

      R. A. Thompson (The American Society of Mechanical Engineers (ASME), 1974)
      Traditionally, grinder stability analyses have been based on Laplace Transform techniques. In this paper an alternative approach is developed which takes into account the wear and speed of both ...

    • Optimum Design and Control of Underwater Gliders 

      A. Baz; A. Seireg (The American Society of Mechanical Engineers (ASME), 1974)
      This study deals with the optimum design of an underwater glider that utilizes buoyancy control as a means of propulsion. The glider’s hydrodynamic lifting surfaces are designed for maximum ...

    • Active Machine Tool Controller Requirements for Noise Attenuation 

      E. E. Mitchell; E. Harrison (The American Society of Mechanical Engineers (ASME), 1974)
      The use of feedback control to regulate the position of the cutting tool relative to the workpiece on a machine tool such as a lathe is examined with respect to the reduction of vibratory ...

    • A Theory of Nonlinear Regenerative Chatter 

      N. H. Hanna; S. A. Tobias (The American Society of Mechanical Engineers (ASME), 1974)
      A mathematical theory of nonlinear chatter is developed. In this, the structure is represented by an equivalent single degree of freedom system with nonlinear stiffness characteristics and the ...

    • Assessment of Ultimate Fidelity of an Eccentric Circular Disk Cam With Translating Flatfaced Follower as a Function Generator 

      C. Mischke (The American Society of Mechanical Engineers (ASME), 1974)
      It is generally known that an eccentric circular disk cam actuating a flatfaced translating follower is an economical approximate function generator. The designer’s question is “Just how well ...

    • Reliability and Economic Analyses Applied to Mechanical Equipment 

      N. W. Nelson; K. Hayashi (The American Society of Mechanical Engineers (ASME), 1974)
      An approach is presented whereby the design and replacement of finite life equipment may be approached in a rational manner. Considering manufacturing operations large enough to give a sufficient ...