Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1621-1640 of 7723
-
High Rake Angle Orthogonal Machining of Highly Ordered Pyrolytic Graphite Parallel to the Basal Plane
(The American Society of Mechanical Engineers (ASME), 2016)High rake angle orthogonal machining of highly ordered pyrolytic graphite (HOPG) parallel to the basal plane was carried out to synthesize few layers of graphene. The quality of the graphite sheets was found to be an ... -
A Discussion on Removal Mechanisms in Grinding Polycrystalline Diamond
(The American Society of Mechanical Engineers (ASME), 2016)Polycrystalline diamond (PCD) grinding takes an important role in the field of tool manufacture. Regardless, there is still lack of process knowledge about the occurring material removal mechanisms in PCD grinding. In order ... -
Precision Forming of the Straight Edge of Square Section by Die-Less Spinning
(The American Society of Mechanical Engineers (ASME), 2016)Die-less spinning is a forming process to achieve cone shape parts. It is suitable for small batch production because of low costs and short development cycle. In order to increase the forming accuracy of the square section ... -
Predicting Distortion in Butt Welded Plates Using an Equivalent Plane Stress Representation Based on Inherent Shrinkage Volume
(The American Society of Mechanical Engineers (ASME), 2016)Due to the adverse effect that distortion has on assembly fit-up and fabrication costs in welded structures, the ability to predict dimensional changes represents an important engineering concern. While distortion can be ... -
Experimental and Numerical Analysis of Filament Front Deformation for Direct-Print
(The American Society of Mechanical Engineers (ASME), 2016)The purpose of this research is to perform an investigation of continuously dispensed material (or filament) deformation during dispensing. Depending on the material properties, and the process parameters the deformation ... -
The Undercut Criterion of Pinion Shaper Cutters: And an Improvement by Modifying the Basic Rack Profile
(The American Society of Mechanical Engineers (ASME), 2016)The fillet of the gear tooth is highly stressed in operation; so for heavily loaded gears, the fillet geometry must be controlled. The manufacturer's task is to, within acceptable tolerances, produce the gear to the ... -
Calibration and Validation of a Mechanistic Micromilling Force Prediction Model
(The American Society of Mechanical Engineers (ASME), 2016)Mechanistic force prediction models require a calibration phase to determine the cutting coefficients describing the tool–target material interaction. The model prediction performance depends on the experimental correctness ... -
Discussion: “Analysis and Design of Tangent Elasticity Vibration Isolators” (Ruzicka, Jerome E., 1961, ASME J. Eng. Ind., 83, pp. 53–59)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “An Analysis of the Yielded Compound Cylinder” (Becker, S. J., 1961, ASME J. Eng. Ind., 83, pp. 43–47)
(The American Society of Mechanical Engineers (ASME), 1961) -
Discussion: “Stresses in Thin-Walled Pressure Vessels With Ellipsoidal Heads” (Kraus, H., Bilodeau, G. G., and Langer, B. F., 1961, ASME J. Eng. Ind., 83, pp. 29–40)
(The American Society of Mechanical Engineers (ASME), 1961) -
Optimum Design of Helical Compression Springs
(The American Society of Mechanical Engineers (ASME), 1961)The most efficient spring, for a given application, is one that safely stores the required amount of energy and uses the least possible material. Springs designed to this premise are said to ... -
Shaft Whirling as Influenced by Stiffness Asymmetry
(The American Society of Mechanical Engineers (ASME), 1961)Using elementary apparatus and instrumentation, shaft whirling has been investigated for three cases involving round or flattened shafts in combination with uniform or asymmetric stiffness bearing ... -
On the Determination of the Influence of an Axial Preload Owing to Bolting on a Cylindrical Pressure Vessel
(The American Society of Mechanical Engineers (ASME), 1961)An idealization of a cylindrical pressure vessel with end plates fastened by longitudinal bolts is considered. The initial axial preload is restricted to be below the load necessary to begin ... -
Calibration Techniques in Ultrahigh-Pressure Apparatus
(The American Society of Mechanical Engineers (ASME), 1961)Pressure and temperature calibration of ultrahigh-pressure apparatus is described. Pressure calibration up to 30 kilobars has been established accurately. Above this pressures are not known with ... -
Use of a Centrifuge for the Precision Measurement of Accelerometer Characteristics
(The American Society of Mechanical Engineers (ASME), 1961)The large dynamic range to which accelerometers are subjected in a space-injection application requires that precision high “g” development studies be made. The only practical way of obtaining ... -
An Experimental Investigation of the Electrolytic Grinding Process
(The American Society of Mechanical Engineers (ASME), 1961)Data are presented covering the effect of several variables on grinding rate for the electrolytic grinding process. The relative amount of material removal due to electrolysis and due to ... -
Free Machining Steel: III—Cutting Forces; Surface Finish and Chip Formation
(The American Society of Mechanical Engineers (ASME), 1961)Tests upon a variety of friction sliders reveal that, contrary to common belief, manganese sulfide is a poor solid lubricant relative to air. Lead, on the other hand, is found to be an ... -
Free Machining Steel: II—Tool-Life Characteristics of Leaded Steel
(The American Society of Mechanical Engineers (ASME), 1961)High-speed steel tool life results are presented and discussed for a leaded and nonleaded steel from the same heat. Variables investigated include cutting speed, feed, cutting fluid, and cold work. -
Free Machining Steel: I—Tool-Life Characteristics of Resulfurized Steel
(The American Society of Mechanical Engineers (ASME), 1961)Tool-wear and tool-life characteristics of a series of five steels of different sulfur content are presented for different values of cutting speed, feed, cutting fluid, and cold work. While the ... -
A Milling Torquemeter of Planetary-Gear Design
(The American Society of Mechanical Engineers (ASME), 1961)A design of planetary-gear dynamometer or torquemeter, to measure tangential cutting forces in milling with a high degree of accuracy and sensitivity is described together with certain design ...