Journal of Manufacturing Science and Engineering: Recent submissions
Now showing items 1601-1620 of 7723
-
Partial Differential Equation-Based Multivariable Control Input Optimization for Laser-Aided Powder Deposition Processes
(The American Society of Mechanical Engineers (ASME), 2016)This paper deals with the systematic optimization method for multiple input variables (laser irradiation power and scanning speed) in a class of laser-aided powder deposition (LAPD) processes. These processes are normally ... -
High-Definition Metrology Enabled Surface Variation Control by Cutting Load Balancing1
(The American Society of Mechanical Engineers (ASME), 2016)This paper presents a method to reduce surface variation in face milling processes based on high-definition metrology (HDM) measurements. Our previous research has found and established the relations between surface variation ... -
A Local-to-Global Dimensional Error Calculation Framework for the Riveted Assembly Using Finite-Element Analysis
(The American Society of Mechanical Engineers (ASME), 2016)Mechanical structures of large-scale antennas are sheet metals connected by thousands of rivets. The antenna dimensional error after riveting often violates the limit allowed. The prediction of the global dimensional error ... -
A Study on Native Oil Components Depletion of Industrial Metalworking Fluid During Microfiltration
(The American Society of Mechanical Engineers (ASME), 2016)The depletion of native oil components from semisynthetic metalworking fluids (MWFs) during microfiltration is caused in part by the deposition of the MWF components on the pore walls, a mechanism that also results in the ... -
Measurement of the Friction Force Inside the Needle in Biopsy
(The American Society of Mechanical Engineers (ASME), 2016)Core needle biopsy (CNB) is widely used in active surveillance, which is the current standard of care for low risk prostate cancers. A longer biopsy sample length may improve the accuracy of diagnosis. To increase the ... -
Fatigue Life Improvement of Holed Plates Made of an Innovative Medium C Micro-Alloyed Steel by Local Plastic Deformation
(The American Society of Mechanical Engineers (ASME), 2016)This paper deals with the influence of local plastic deformation on the fatigue strength of holed plates manufactured with an innovative medium-carbon micro-alloyed steel with high silicon content (hi-Si MCM). Local ... -
Experimental and Numerical Investigation of Laser Forming of Closed-Cell Aluminum Foam
(The American Society of Mechanical Engineers (ASME), 2016)Aluminum foams are generally very attractive because of their ability of combining different properties such as strength, light weight, thermal, and acoustic insulation. These materials, however, are typically brittle under ... -
Straight Bevel Gear Generation Using the Dual Interlocking Circular Cutter Cutting Method on a Computer Numerical Control Bevel Gear-Cutting Machine
(The American Society of Mechanical Engineers (ASME), 2016)The dual interlocking circular cutter (DICC) cutting method, used to produce straight bevel gears (SBGs), employs two interlocked cutters to generate tooth surfaces with a combination of profile and lengthwise crowning. ... -
Learning Approach to Cycle-Time-Minimization of Wood Milling Using Adaptive Force Control
(The American Society of Mechanical Engineers (ASME), 2016)A majority of the machining processes in the industry of today are performed using position-controlled machine tools, where conservative feed rates have to be used in order to avoid excessive process forces. Instead of ... -
Improvements to the Iterative Closest Point Algorithm for Shape Registration in Manufacturing
(The American Society of Mechanical Engineers (ASME), 2016)Iterative closest point (ICP) is a popular algorithm used for shape registration while conducting inspection during a production process. A crucial key to the success of the ICP is the choice of point selection method. ... -
Silicone Rubber Properties During Consolidation/Curing of Advanced Composites Using Specialized Elastomeric Tooling
(The American Society of Mechanical Engineers (ASME), 2016)Specialized elastomeric tooling (SET) is a patented process that can replace autoclaving for consolidating and curing advanced thermoset and thermoplastic composite parts. The process mimics autoclave conditions of uniform ... -
An Assessment of the Wear Characteristics of Microcutting Arrays Produced From Polycrystalline Diamond and Cubic Boron Nitride Composites
(The American Society of Mechanical Engineers (ASME), 2016)The current methods for manufacturing super-abrasive elements result in a stochastic geometry of abrasives with random three-dimensional abrasive locations. This paper focuses on the evaluation of wear progression/failure ... -
A Three-Dimensional Transient Thermal Model for Machining
(The American Society of Mechanical Engineers (ASME), 2016)This article presents an enhanced mathematical model for transient thermal analysis in machining processes. The proposed mathematical model is able to simulate transient tool, workpiece, and chip temperature fields as a ... -
Calculation Method for Rocking Die Motion Track in Cold Orbital Forging
(The American Society of Mechanical Engineers (ASME), 2016)In cold orbital forging, the rocking die performs complex motions on the components and the intervention between them cannot emerge, otherwise the components cannot be shaped successfully. Calculating the rocking die motion ... -
Laser Additive Manufacturing of Novel Aluminum Based Nanocomposite Parts: Tailored Forming of Multiple Materials
(The American Society of Mechanical Engineers (ASME), 2016)The present study has proved the feasibility to produce the bulk-form TiC/AlSi10Mg nanocomposite parts with the novel reinforcing morphology and enhanced mechanical properties by selective laser melting (SLM) additive ... -
Prediction of Residual Stresses During Gas Nitriding of H13 Steels Using Phase Field Approach
(The American Society of Mechanical Engineers (ASME), 2016)Gas nitriding is a common surface treatment practice to improve the wear resistance of AISI H13 hot extrusion die cavities. However, due to the presence of complex and sharp features of die cavities, it has been observed ... -
Multiscale Finite Element Modeling of Alumina Ceramics Undergoing Laser-Assisted Machining
(The American Society of Mechanical Engineers (ASME), 2016)Alumina ceramics, due to their excellent properties of high hardness, corrosion resistance, and low thermal expansion coefficient, are important industrial materials with a wide range of applications, but these materials ... -
Influence of Deformational Cutting Data on Parameters of Polymer Slotted Screen Pipes
(The American Society of Mechanical Engineers (ASME), 2016)A method for manufacturing polymer slotted screen pipes by the use of deformational cutting (DC) technology is presented in this paper. The slotted macrostructure is created by cutting through the pipe wall without chip ... -
Experimental Investigation of Residual Stress in Minimum Quantity Lubrication Grinding of AISI 1018 Steel
(The American Society of Mechanical Engineers (ASME), 2016)Minimum quantity lubrication (MQL) is a promising alternative to conventional flood cooling to substantially reduce lubricant cost and converse energy. Literature survey shows lack of investigation on the influence of MQL ... -
Fracture Mechanics Model of Needle Cutting Tissue
(The American Society of Mechanical Engineers (ASME), 2016)This work develops a needle insertion force model based on fracture mechanics, which incorporates the fracture toughness, shear modulus, and friction force of the needle and tissue. Ex vivo tissue experiments were performed ...