Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3621-3640 of 4506
-
Computational Heat Transfer
(The American Society of Mechanical Engineers (ASME), 1987) -
Development of Design Criteria for a High Pressure Vessel Construction Code
(The American Society of Mechanical Engineers (ASME), 1987)Out of concern for public safety, most legal jurisdictions now require unfired pressure vessel construction to comply with the ASME Boiler and Pressure Vessel Code. Because the present two ... -
High Temperature Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1987) -
Heat Transfer and Fluid Flow in Rotating Machinery
(The American Society of Mechanical Engineers (ASME), 1987) -
High Temperature Equipment
(The American Society of Mechanical Engineers (ASME), 1987) -
Managing Steam (An Engineering Guide to Commercial, Industrial and Utility Systems)
(The American Society of Mechanical Engineers (ASME), 1987) -
A Tribute to the Late Irwin Berman
(The American Society of Mechanical Engineers (ASME), 1987) -
Irwin Berman
(The American Society of Mechanical Engineers (ASME), 1987) -
Stress Analysis of Elliptical Tube Plates in Heat Exchangers
(The American Society of Mechanical Engineers (ASME), 1987)Elliptical tube plates are used widely in high temperature, high pressure heat exchangers and waste heat boilers. This paper presents a detailed analysis of the stress distribution in elliptical ... -
Structural Assessment Techniques for Thermal Striping
(The American Society of Mechanical Engineers (ASME), 1987)Life assessment techniques for components subject to random surface temperature fluctuations (thermal striping) are outlined. The approach depends on the thermal information available and ranges ... -
Application of the Ritz Averaging Method in the Analysis of the Seismic Performance of Piping Systems
(The American Society of Mechanical Engineers (ASME), 1987)The Ritz averaging method is utilized to reduce the nonlinear characteristics of piping system supports (snubbers) to equivalent linear support stiffnesses during seismic excitation. The equivalent ... -
Fatigue Life of Seamless Steel Pressure Vessels
(The American Society of Mechanical Engineers (ASME), 1987)Cyclic-pressure fatigue tests of three seamless steel pressure vessels show that typical production vessels should have a fatigue life at least equal to the allowable life calculated by code ... -
An Unusual Mode of Collapse of Tubes Under Combined Bending and Pressure
(The American Society of Mechanical Engineers (ASME), 1987) -
The Chemical Engineering Guide to Heat Transfer (Volume I: Plant Principles, Volume II: Equipment)
(The American Society of Mechanical Engineers (ASME), 1987) -
Aerothermodynamics of Low Pressure Steam Turbines and Condensers
(The American Society of Mechanical Engineers (ASME), 1987) -
Dynamic Stability of Pipes Under Jet Forces From a Circumferential Through-Crack
(The American Society of Mechanical Engineers (ASME), 1987)An investigation is made into the dynamic stability of a pipe with a postulated circumferential through-crack. The dynamic deformation of the pipe is found to control the ensuing jet force in ... -
Residual Stress Effects on Fatigue Crack Growth Behavior in Stainless Steel Welds
(The American Society of Mechanical Engineers (ASME), 1987)Standard fatigue precracking of fracture toughness specimens taken from stainless steel welds with a double-V design was found to result in extremely uneven crack fronts. Material variability ... -
Primary Creep Analysis of an Anisotropic Thick-Walled Spherical Shell
(The American Society of Mechanical Engineers (ASME), 1987)The problem of primary creep of an orthotropic thick-walled spherical shell under internal pressure has been analyzed in this paper. The creep stresses and strains have been calculated using a ... -
An Analytical Model of Strength Loss in Filament Wound Spherical Vessels
(The American Society of Mechanical Engineers (ASME), 1987)The potential strength degradation of a filament wound sphere was predicted using an incremental finite element model of the composite during fabrication. The sphere was modeled taking into ... -
Elastic-Plastic Plane Strain Analysis of Compressible Materials
(The American Society of Mechanical Engineers (ASME), 1987)The analysis of elastic, perfectly plastic compressible materials under the assumption of plane strain is a statically indeterminate problem. In the present paper, by introducing a perturbation ...