Journal of Pressure Vessel Technology: Recent submissions
Now showing items 3641-3660 of 4506
-
Handbook of Heat and Mass Transfer, Volumes One and Two
(The American Society of Mechanical Engineers (ASME), 1987) -
Handbook of Hydraulic Resistance, 2nd Edition
(The American Society of Mechanical Engineers (ASME), 1987) -
Further Development of a Model for Predicting Corrosion Fatigue Crack Growth in Reactor Pressure Vessel Steels
(The American Society of Mechanical Engineers (ASME), 1987)Analysis of fatigue crack growth data for low-alloy steel shows that the influence of cyclic frequency in simulated LWR environments can be interpreted as the superposition of a time-dependent, ... -
Pressure-Plus-Moment Limit-Load Analysis for a Cylindrical Shell Nozzle
(The American Society of Mechanical Engineers (ASME), 1987)A finite element model of a nozzle in a cylindrical shell is analyzed for three cases; pressure, out-of-plane moment and combined pressure plus out-of-plane moment. The model uses three-dimensional ... -
Acoustic Resonance in Heat Exchanger Tube Bundles—Part II: Prediction and Suppression of Resonance
(The American Society of Mechanical Engineers (ASME), 1987)In the first part of this series, experimental data were presented which suggest that the acoustic resonance in heat exchanger tube bundles is tied to periodic vortex shedding from the tubes. ... -
A Model for Fixed-Tubesheet Heat Exchanger
(The American Society of Mechanical Engineers (ASME), 1987)A model for a fixed-tubesheet heat exchanger was developed under the assumption that the outer rim of the tubesheet behaves as a circular plate. The tubesheet is conceived as made up of two ... -
Fracture Toughness of Aged Stainless Steel Primary Piping and Reactor Vessel Materials
(The American Society of Mechanical Engineers (ASME), 1987)The ductile fracture toughness behavior of FFTF primary piping and reactor vessel construction materials was characterized using the multiple-specimen J R -curve technique before and after 10,000-hr ... -
Experimental Verification of Fracture Toughness Requirement for Leak-Before-Break Performance for 155–175 ksi Strength Level Gas Cylinders
(The American Society of Mechanical Engineers (ASME), 1987)This paper deals with a determination of the fracture toughness requirement to obtain leak-before-break performance for a 155–175 ksi strength level high-pressure gas cylinder. Analytical LEFM ... -
Modeling of 316 Stainless Steel (17.12 Sph.) Mechanical Properties Using Biaxial Experiments—Part I: Experiments and Basis of the Model
(The American Society of Mechanical Engineers (ASME), 1987)Experimental results aimed at establishing the relationship existing between plastic instantaneous and creep strains are reported. They are chiefly tensile at constant strain rates and tensile or ... -
Modeling of 316 Stainless Steel (17.12 Sph.) Mechanical Properties Using Biaxial Experiments—Part II: Model and Simulation
(The American Society of Mechanical Engineers (ASME), 1987)A rheological model aimed at accounting for the existence of two types of viscoplastic flow (microplastic and macroplastic) in 316 stainless steel is described in the most general state of ... -
Creep Relaxation in Multilayer Wrapped Vessels
(The American Society of Mechanical Engineers (ASME), 1987)One of the common methods of construction of vessels for high to ultra-high pressure applications is the wrapping technique. In this method, relatively thin plates (normally in the range of 6 ... -
A Theoretical Assessment of Napier’s Law
(The American Society of Mechanical Engineers (ASME), 1987)Napier’s Law is advantageous for calculating critical mass flow rate of water-steam mixture. On the basis of numerical computations, it has been recently extended to a number of fluids. A ... -
Erratum: “Development of Design Criteria for a High Pressure Vessel Construction Code” (Journal of Pressure Vessel Technology, 1987, 109, p. 258)
(The American Society of Mechanical Engineers (ASME), 1987) -
Pressure Vessel Design Handbook, 2nd Edition
(The American Society of Mechanical Engineers (ASME), 1987) -
Acoustic Resonance in Heat Exchanger Tube Bundles—Part I: Physical Nature of the Phenomenon
(The American Society of Mechanical Engineers (ASME), 1987)The intense acoustic resonance resulting from gas flow across a bank of heat exchanger tubes in a duct has been investigated experimentally and theoretically. At low gas velocities, the acoustic ... -
Experimental Study on Impact/Fretting Wear in Heat Exchanger Tubes
(The American Society of Mechanical Engineers (ASME), 1987)The objective of this study is to provide qualitative impact/fretting wear information for heat exchanger tubes through the performance of a series of tests involving the pertinent parameters: ... -
Vibration and Stability of Helical Pipes Conveying Fluid
(The American Society of Mechanical Engineers (ASME), 1987)This paper presents an accurate finite element procedure for the vibration and stability analysis of helical pipe conveying fluid. The kinematics of the helical pipe are derived including the ... -
Collapse Characteristics of a Thin-Walled Elbow: Validation of an Analytical Procedure
(The American Society of Mechanical Engineers (ASME), 1987)A nonlinear analysis procedure is validated in this paper to predict deformation response, up to collapse, of thin-walled Liquid Metal Reactor (LMR) piping elbows. Nonlinear shell analysis ... -
Comparison of Theoretical Estimates and Experimental Measurements of Fatigue Crack Growth Under Severe Thermal Shock Conditions—Part II: Theoretical Assessment and Comparison With Experiment
(The American Society of Mechanical Engineers (ASME), 1987)This paper reports the theoretical assessment of cracking which may occur when a severe cycle comprising alternate upshocks and downshocks is applied to an axisymmetric feature with an internal, ... -
A Finite Element Model to Analyze Cylinder-Cylinder Intersections
(The American Society of Mechanical Engineers (ASME), 1987)A finite element model is proposed to study the stresses in the neighborhood of a cylinder-cylinder intersection. In particular, diameter ratios greater than 0.5 are focused upon since little ...