Journal of Engineering Materials and Technology: Recent submissions
Now showing items 981-1000 of 3257
-
The Influence of Ultrasonic Energy on Chemical Treatment of Surface Properties and the Properties of Composites Made of Luffa Cylindrical Fiber-Polyester Resin
(The American Society of Mechanical Engineers (ASME), 2008)Producing composites from natural fibers is known to be common. These fibers benefit from their mechanical performances, low density, and their biodegradability. However, it is necessary for the ... -
Improvement of Formability and Spring-Back of AA5052-H32 Sheets Based on Surface Friction Stir Method
(The American Society of Mechanical Engineers (ASME), 2008)A process to improve formability and spring-back was developed for AA5xxx-H temper sheets based on the surface friction stir (SFS) method. In the SFS method, a rotating probe stirs the sheet ... -
Effect of Laser Welding on Formability of DP980 steel
(The American Society of Mechanical Engineers (ASME), 2008)Limiting dome height (LDH) tests were used to evaluate the formability of laser butt welded blanks of the dual phase 980 steel in comparison with the base metal. Two different lasers were ... -
Effect of Shape of the Tip in Determining Interphase Properties in Fiber Reinforced Plastic Composites Using Nanoindentation
(The American Society of Mechanical Engineers (ASME), 2008)Fiber reinforced polymer composites are two component material systems in which fibers are embedded in a polymer matrix. Such a system inherently has an interface where the two components meet. ... -
Development of a Multiaxial Fatigue Damage Model for High Strength Alloys Using a Critical Plane Methodology
(The American Society of Mechanical Engineers (ASME), 2008)The prediction of fatigue life for metallic components subjected to complex multiaxial stress states is a challenging aspect in design. Equivalent-stress approaches often work reasonably well for ... -
Characterization and Modeling of Large Displacement Micro-/Nano-Indentation of Polymeric Solids
(The American Society of Mechanical Engineers (ASME), 2008)Large displacement micro-indentation tests have been performed on various polymeric solids to measure the plastic properties. Cylindrical flat-ended indenters with diameter in the range of 10–90 ... -
Discussion: “On the Reference Length and Mode Mixity for a Bimaterial Interface” (Agrawal, A., and Karlsson, A. M., 2007, ASME J. Eng. Mater. Technol., 129, pp. 580–587)
(The American Society of Mechanical Engineers (ASME), 2008)In a recent paper (1), the authors revisited a basic question of interfacial fracture mechanics, namely, the choice of the characteristic reference lengthlc in the open model of interface cracks ... -
Closure to “Discussion: ‘On the Reference Length and Mode Mixity for a Bimaterial Interface’ ” (2008, ASME J. Eng. Mater. Technol., 130, p. 045501)
(The American Society of Mechanical Engineers (ASME), 2008)The method proposed by Agrawal and Karlsson (1) is correct when assuming a symmetric interfacial fracture toughness curve. Based on the resolution (e.g., the scatter in the data) from the ... -
Impact Damage Tolerance and Fatigue Durability of GLARE Laminates
(The American Society of Mechanical Engineers (ASME), 2008)The fatigue behavior and residual strength of postimpacted GLARE 4-3/2, GLARE 5-2/1, and monolithic aluminum 2024-T3 alloy were investigated experimentally. Drop-weight impact was applied at a ... -
Some Aspects on Hot Forging Features of P/M Sintered High-Strength Titanium Carbide Composite Steel Preforms Under Different Stress State Conditions
(The American Society of Mechanical Engineers (ASME), 2007)Experiments were carried out to evaluate the hot forging features in the high-strength sintered Powder Metallurgy TiC composite steel performs under different stress states, namely, plane and ... -
Effect of Strain Gage Length When Determining Residual Stress by Slitting
(The American Society of Mechanical Engineers (ASME), 2007)This paper investigates the effect of strain gage length on residual stress estimated by the slitting (or crack compliance) method. This effect is quantified for a range of gage length normalized ... -
Effect of Atomization Method on the Morphology of Spray-Generated Particles
(The American Society of Mechanical Engineers (ASME), 2007)Effect of various atomization methods and solute concentration on the morphology of spray dried magnesium sulphate particles is investigated. Four types of atomizers are characterized and tested ... -
Experimental and Theoretical Analysis on Formability of Aluminum Tailor-Welded Blanks
(The American Society of Mechanical Engineers (ASME), 2007)This paper presents an investigation on forming limits of tailor-welded blanks (TWBs) made of 5754-O aluminum sheets using both experimental and numerical approaches. TWBs may be composed of two ... -
A Statistical Methodolgy for the Preparation of a Competing Modes Fatigue Design Curve
(The American Society of Mechanical Engineers (ASME), 2007)A methodology is presented for the preparation of a competing modes fatigue design curve. Examples using extruded and isothermally forged powder metallurgy René 95 are presented. Monte Carlo ... -
Methodology for Determining the Variance of the Taylor Factor: Application in Fe-3%Si
(The American Society of Mechanical Engineers (ASME), 2007)A method is proposed to determine the variance of an arbitrary material property based on the statistics of the texture of polycrystalline materials for a specified volume. This method is ... -
A Multiscale Analysis of Void Coalescence in Nickel
(The American Society of Mechanical Engineers (ASME), 2007)An internal state variable void coalescence equation developed by , , , and (2000, Theor. Appl. Fract. Mech., 33(1), pp. 31–47) that comprises void impingement and void sheet mechanisms is ... -
Characterization of Polypropylene Nanocomposite Structures
(The American Society of Mechanical Engineers (ASME), 2007)This study describes the synthesis, mechanical properties, and morphology of nanophased polypropylene structures. The structures were manufactured by melt-blending low weight percentages of montmorillonite ... -
Development of Short Fiber-Reinforced NiTi∕Al6061 Composite
(The American Society of Mechanical Engineers (ASME), 2007)The aluminum matrix composite reinforced by short NiTi shape memory alloy fibers, NiTi∕Al6061 composite, was fabricated using pressure-assisted sintering process in ambient air. Surface preparation ... -
Residual Elastic Strains in Autofrettaged Tubes: Elastic–Ideally Plastic Model Analysis
(The American Society of Mechanical Engineers (ASME), 2007)Autofrettage is a treatment process that uses plastic deformation to create a state of permanent residual stress within thick-walled tubes by pressurizing them beyond the elastic limit. The ... -
Using In Situ Atomic Force Microscopy to Investigate the Kinetics of Corrosion of WC–Co–Cr Cermet Coatings Applied by High-Velocity Oxy-Fuel
(The American Society of Mechanical Engineers (ASME), 2007)Most of the early applications of thermal spray coatings were focused toward providing a remedy to excessive wear degradation. However, as the introduction of such coatings into wider industrial ...