Journal of Engineering Materials and Technology: Recent submissions
Now showing items 941-960 of 3257
-
Advances in Virtual Metal Forming Including the Ductile Damage Occurrence: Application to 3D Sheet Metal Deep Drawing
(The American Society of Mechanical Engineers (ASME), 2008)An advanced numerical methodology to simulate virtually any sheet or bulk metal forming including various kinds of initial and induced anisotropies fully coupled to the isotropic ductile damage ... -
Multiproperty Microstructure and Property Design of Magnetic Materials
(The American Society of Mechanical Engineers (ASME), 2008)Microstructure sensitive design was used in this study to design a textured soft magnet material to meet a range of magnetic properties. The evolution of microstructure and magnetic properties ... -
Dislocation Density Tensor Characterization of Deformation Using 3D X-Ray Microscopy
(The American Society of Mechanical Engineers (ASME), 2008)Three-dimensional (3D) X-ray microscopy with submicron resolution has been used to make spatially resolved measurements of lattice curvature and elastic strain over two-dimensional slices in thin ... -
Effect of Size-Dependent Cavitation on Micro- to Macroscopic Mechanical Behavior of Rubber-Blended Polymer
(The American Society of Mechanical Engineers (ASME), 2008)In rubber-blended polymer, the onset of cavitation in the particles relaxes the high triaxiality stress state and suppresses the onset of crazing in the polymer. As a result, large plastic ... -
Hot Tearing in Steels During Solidification: Experimental Characterization and Thermomechanical Modeling
(The American Society of Mechanical Engineers (ASME), 2008)Hot tearing is a major defect in castings or semifinished cast products. It corresponds to the opening of cracks in the mushy zone and, more precisely, in the areas with high fraction of ... -
Probing Microstructure Dynamics With X-Ray Diffraction Microscopy
(The American Society of Mechanical Engineers (ASME), 2008)We describe our recent work on developing X-ray diffraction microscopy as a tool for studying three dimensional microstructure dynamics. This is a measurement technique that is demanding of ... -
Crack Tip Fields in a Single Edge Notched Aluminum Single Crystal Specimen
(The American Society of Mechanical Engineers (ASME), 2008)We report a combined experimental and computational study of a low constraint aluminum single crystal fracture geometry and investigate the near-tip stress and strain fields. To this end, a ... -
Nonlocal Modeling and Simulation of Ductile Damage and Failure in Metal Matrix Composites
(The American Society of Mechanical Engineers (ASME), 2008)The purpose of the current work is the application of a recent nonlocal extension (, , and , 2003, “ Local and Non-Local Gurson-Based Ductile Damage and Failure Modelling at Large Deformation,” ... -
On Predicting Nucleation of Microcracks Due to Slip-Twin Interactions at Grain Boundaries in Duplex Near γ-TiAl
(The American Society of Mechanical Engineers (ASME), 2008)(2003, “ A Factor to Predict Microcrack Nucleation at Gamma-Gamma Grain Boundaries in TiAl,” Scr. Mater., 49(2), 149–154) proposed a relationship for predicting crack initiation in γ-TiAl in a ... -
Damage Development During Superplasticity of Light Alloys
(The American Society of Mechanical Engineers (ASME), 2008)Superplastic forming (SPF) of metallic alloys allows the production of components with particularly complex shapes since in this regime, due to the predominance of grain boundary sliding (GBS), ... -
Modeling Damage Evolution in Friction Stir Welding Process
(The American Society of Mechanical Engineers (ASME), 2008)The evolution of voids (damage) in friction stir welding processes was simulated using a void growth model that incorporates viscoplastic flow and strain hardening of incompressible materials ... -
In Situ Imaging of High Cycle Fatigue Crack Growth in Single Crystal Nickel-Base Superalloys by Synchrotron X-Radiation
(The American Society of Mechanical Engineers (ASME), 2008)A novel X-ray synchrotron radiation approach is described for real-time imaging of the initiation and growth of fatigue cracks during ultrasonic fatigue (f=20kHz). We report here on new insights ... -
Effects of Manufacturing-Induced Voids on Local Failure in Polymer-Based Composites
(The American Society of Mechanical Engineers (ASME), 2008)This paper presents results of a computational study focused on examining the role of manufacturing-induced voids in the initiation and growth of damage at the microstructural level in polymer ... -
A Natural Neighbor Method Based on Fraeijs de Veubeke Variational Principle for Elastoplasticity and Fracture Mechanics
(The American Society of Mechanical Engineers (ASME), 2008)The natural neighbor method can be considered as one of the many variants of the meshless methods. Classically, the development of these methods is based on the virtual work principle: A set ... -
Dynamic Dislocation-Defect Analysis and SAXS Study of Nanovoid Formation in Aluminum Alloys
(The American Society of Mechanical Engineers (ASME), 2008)Crystalline defects other than the essential dislocations are produced by dislocation intersections resulting in debris, which can transform into loops, point defects, and∕or nanovoids. The stress ... -
Densification, Microstructure, and Behavior of Hydroxyapatite Ceramics Sintered by Using Spark Plasma Sintering
(The American Society of Mechanical Engineers (ASME), 2008)This paper discusses the dependence of the mechanical properties and microstructure of sintered hydroxyapatite (HA) on the sintering temperature and pressure. A set of specimens was prepared from ... -
A Study on the Design and Mechanical Adhesion of Polymer Foam-Metal Joints
(The American Society of Mechanical Engineers (ASME), 2008)The design of metal-polymer foam adhesion and load transfer characteristics is carried out in this research work. The metal inserts are used as the load transfer component, while the foam is ... -
Defect Occurrence and Modeling for the Thermomechanical Processing of Aerospace Alloys
(The American Society of Mechanical Engineers (ASME), 2008)Mechanism-based models for the evolution of defects during the thermomechanical processing of aerospace titanium- and nickel-based alloys are reviewed. These defects include those comprising ... -
Modeling Strain Localization Using a Plane Stress Two-Particle Model and the Influence of Grain Level Matrix Inhomogeneity
(The American Society of Mechanical Engineers (ASME), 2008)The role of dilute small particles on the development of strain localization under uniaxial tension has been studied by finite element analysis using a plane stress model with two small hard ... -
Materials Processing Defects
(The American Society of Mechanical Engineers (ASME), 2008)The papers in this special edition came from lectures delivered at the Fifth International Conference on Materials Processing Defects (MPD-5) held at Cornell University July 18–20, 2007 at Cornell ...