Journal of Engineering Materials and Technology: Recent submissions
Now showing items 3001-3020 of 3257
-
A Cumulative Damage Rule Based on Successive Reduction in Fatigue Limit
(The American Society of Mechanical Engineers (ASME), 1978) -
Evaluation of the Creep Resistance of Wire Rope End Attachments
(The American Society of Mechanical Engineers (ASME), 1978) -
Influence of Selenium and Tellurium on the Fatigue of Low-Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1978) -
Void Growth and Local Necking in Biaxially Stretched Sheets
(The American Society of Mechanical Engineers (ASME), 1978)The role of void growth in triggering local necking in biaxially stretched sheets is investigated. A recently proposed constitutive equation for porous plastic materials is employed in conjunction ... -
Cryogenic Tensile, Fatigue, and Fracture Parameters for a Solution-Annealed 18 Percent Nickel Maraging Steel
(The American Society of Mechanical Engineers (ASME), 1978)The mechanical properties of an eighteen percent nickel, solution-annealed 300-grade maraging steel were measured to assist in the evaluation of this material for low-temperature structural ... -
Stress-Strain Analysis of Cyclic Plastic Bending and Torsion
(The American Society of Mechanical Engineers (ASME), 1978)Analysis of stresses, strains, and damping energies is considered for cyclic loading of simple geometries. For beams under pure bending and for circular shafts under torsion, it is shown that ... -
A Weakest-Link Model for the Prediction of Fatigue Crack Growth Rate
(The American Society of Mechanical Engineers (ASME), 1978)A weakest-link theory is proposed for analyzing the rate of fatigue crack growth. The joint probability density of a fatigue crack growing an amount X between x and x+dx, and in time η ... -
Combined Mode Fracture Toughness Measurement by the Disk Test
(The American Society of Mechanical Engineers (ASME), 1978)The disk test in which a circular specimen with an internal crack is subjected to diametral compression is used to investigate combined mode I and mode II fracture. The stress intensity factors ... -
General Yielding of Charpy V-Notch and Precracked Charpy Specimens
(The American Society of Mechanical Engineers (ASME), 1978)By applying a slip-line fields solution for general yielding, which includes the tup indenter for Charpy V-notch and precracked Charpy tests, estimates of high loading-rate yield stress values ... -
Closure to “Discussion of ‘Properties of Extra Low Sulfur Engineering and Die Steels’” (1978, ASME J. Eng. Mater. Technol., 100, p. 223)
(The American Society of Mechanical Engineers (ASME), 1978) -
Fracture Mechanics Approach to Fatigue Analysis in Design
(The American Society of Mechanical Engineers (ASME), 1978)Many engineering structures are subjected to cyclically varying (fatigue) loads during service. Fatigue analysis, or the estimation of fatigue lives on such structures, is therefore an essential ... -
Discussion: “Properties of Extra Low Sulfur Engineering and Die Steels” (Wilson, William, 1977 Winter Annual Meeting)
(The American Society of Mechanical Engineers (ASME), 1978) -
An Experimental Study of Progressive Strain Growth Due to Thermal-Stress Ratcheting
(The American Society of Mechanical Engineers (ASME), 1978)A special plate-shaped specimen with two symmetrical, straight air gaps in the center portion and a pair of holes for load chucks at the end portion is used for thermal-stress ratcheting ... -
Discussion: “A Parametric Study of Fatigue Crack Growth Behavior in Adhesively Bonded Metallic Structures” (Ratwani, M. M., 1978, ASME J. Eng. Mater. Technol., 100, pp. 46–51)
(The American Society of Mechanical Engineers (ASME), 1978) -
On the Minimum-Commitment Method for Correlation of Creep-Rupture Data
(The American Society of Mechanical Engineers (ASME), 1978) -
Quarter Elliptical Cracks Emanating From Holes in Plates
(The American Society of Mechanical Engineers (ASME), 1978)The finite element-alternating method, a linear elastic solution technique, is refined and applied to problems of quarter-elliptical cracks in irregular bodies. The method involves the iterative ... -
J-Integral Approach to Fracture of Rotating Disk
(The American Society of Mechanical Engineers (ASME), 1978)The J-integral has been used as a fracture criterion for elastic-plastic behavior of metals. It may be pertinent to use the JIc concept for design or nondestructive inspection of rotating disks ... -
Crack Growth Resistance at Low Stress Intensities
(The American Society of Mechanical Engineers (ASME), 1978)A detailed examination of the early stage of slow tear in thin section aluminum, under increasing load, is reported in this study. The relationship between plane strain fracture toughness and ... -
Application of Resistance Curves to Residual Strength Prediction
(The American Society of Mechanical Engineers (ASME), 1978)A resistance curve approach to predicting residual strength of thin-skin structures, under plane stress type fracture, is discussed. Use is made of material resistance obtained in terms of crack ... -
Irradiation Effects on the Behavior of Structural Materials at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1978)The paper provides a qualitative review of the effects of fast neutron irradiation on the mechanical behavior of materials used in the construction of Fast Breeder Reactor Core Components. The ...