Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2801-2820 of 3257
-
Stress Intensity Factors for Corner Cracked Holes Under General Loading Conditions
(The American Society of Mechanical Engineers (ASME), 1981)A linear elastic analysis is conducted with the finite element-alternating method for quarter-elliptical corner cracks located at fastener holes. Mode-one stress intensity factors are presented ... -
Abrasive Wear in Machining: Experiments With Materials of Controlled Microstructure
(The American Society of Mechanical Engineers (ASME), 1981)Evidence is presented to show that hard inclusions in iron-base alloys degrade machinability by reducing cutting tool life. Machining experiments have been carried out on Fe-C-Silica and Fe-C-Alumina ... -
Application of Finite Element Calculations to Residual Stress Measurements
(The American Society of Mechanical Engineers (ASME), 1981)The use of finite element calculations is assessed as a means of analysis of the strain relaxation data from a measurement of residual stress by a material removal method. This application ... -
The Equivalence of the Final Stretch and Crack Tip Opening Angle Criteria for Plane Strain Crack Growth
(The American Society of Mechanical Engineers (ASME), 1981)The equivalence of the final stretch and crack tip opening angle criteria, as applied to the Dugdale-Bilby-Cottrell-Swinden type model for Mode I plane strain crack growth, is demonstrated. This ... -
Long-Life Fatigue Test Results for Two Nickel-Base Structural Alloys
(The American Society of Mechanical Engineers (ASME), 1981)This paper reports the results of fatigue tests on two nickel-base alloys, hot-cold-worked and stress-relieved nickel-chrome-iron Alloy 600 and mill-annealed nickel-chrome-moly-iron Alloy 625 in ... -
The Effect of a Higher Loading Rate on the JIc Fracture Toughness Transition Temperature of HY Steels
(The American Society of Mechanical Engineers (ASME), 1981)The objectives of the study were to extend the JIc transition temperature analysis of earlier work for HY130 to HY80 steel and also to determine the effect of a higher strain rate on the ... -
A Criterion for Plastic Failure of Notched High Strength Steel Structures
(The American Society of Mechanical Engineers (ASME), 1981)A criterion of ductile failure for a high strength steel under a multiaxial state of stress is established. A family of multiaxial stress states at failure is generated from the fracture data ... -
A Statistical Simulation Model of Miner’s Rule
(The American Society of Mechanical Engineers (ASME), 1981)A Monte Carlo simulation model of the classical Miner’s rule for cumulative fatigue damage is devised and implemented for an example of three summands. Results from the simulation are compared ... -
A New Approach to the Evaluation of Fatigue Under Multiaxial Loadings
(The American Society of Mechanical Engineers (ASME), 1981)A critical review of the methods for evaluating fatigue of metals under simple (proportional) and complex (nonproportional) loadings indicates that most of the criteria are expressed in terms ... -
An Analysis of Grain Size and Yield Stress Effects on Stress at Fatigue Limit and Threshold Stress Intensity Factor
(The American Society of Mechanical Engineers (ASME), 1981)Fatigue limits of smooth specimens and threshold stress instensity factors of specimens with large cracks depend on the microstructure of the material. A simple model in which it is assumed ... -
The Effect of Product Form Upon Fatigue-Crack Growth Behavior in Alloy 718
(The American Society of Mechanical Engineers (ASME), 1981)Five different product forms (sheet, plate, bar, forging, and weldments) all taken from the same heat of Alloy 718 were tested at five different temperatures in each of two different heat-treated ... -
Multispecimen Fatigue Crack Propagation Testing
(The American Society of Mechanical Engineers (ASME), 1981)Chains of miniature center-cracked-tension specimens were tested on a conventional testing machine and on a prototypic in-reactor fatigue machine as part of the fusion reactor materials alloy ... -
A Design Approach for Correlating High Temperature Fatigue Crack Growth Over a Wide Range of Parameters
(The American Society of Mechanical Engineers (ASME), 1981)High temperature fatigue crack growth was studied in several materials under various environmental conditions. At temperatures less than one-half of the melting point, creep effects were found ... -
The Creep Rupture Properties of ASME SA 516 (Grade 55) Steel in the Range 426°C to 872°C
(The American Society of Mechanical Engineers (ASME), 1981)The in-air creep-rupture properties of SA-516 (Grade 55) steel have been investigated in the temperature range 426–872°C (800–1600°F). The rupture time and creep rate data have been ... -
A Comparison of Constitutive Relations Incorporating Strain-Rate Hardening
(The American Society of Mechanical Engineers (ASME), 1981) -
Fatigue of Welded Structures (2nd Edition)
(The American Society of Mechanical Engineers (ASME), 1981) -
Methods of Predicting Material Life in Fatigue
(The American Society of Mechanical Engineers (ASME), 1981) -
Fatigue Criteria Under Combined Stresses or Strains
(The American Society of Mechanical Engineers (ASME), 1981)A brief presentation is given of a previously proposed criterion for long-life fatigue under combined alternating and combined static stress. A new criterion is proposed for long-life fatigue ... -
Fatigue Life Predictions of Smooth and Notched Specimens Based on Fracture Mechanics
(The American Society of Mechanical Engineers (ASME), 1981)An elastic plastic fracture mechanics solution for short fatigue cracks in smooth and notched specimens is presented which admits plasticity by replacing the conventional stress term with a ... -
Development of a Procedure for Estimating the High Cycle Fatigue Strength of Some High Temperature Structural Alloys
(The American Society of Mechanical Engineers (ASME), 1981)The generation of strain controlled fatigue data, for the standard strain rate of 4 × 10−3 s−1 , presents a problem when the cycles to failure exceed 105 because of the prohibitively ...