Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2821-2840 of 3257
-
Threshold and Low-Rate Fatigue Crack Growth of a NiMoV Rotor Steel
(The American Society of Mechanical Engineers (ASME), 1981)An automated, computer-controlled K-decreasing technique was used to determine the threshold, ΔKth , and low-rate fatigue crack growth of a NiMoV rotor steel. A more conventional K-increasing ... -
Erratum: “The Fatigue and Toughness Properties of a C-Mn-Cb Plate Steel” (Journal of Engineering Materials and Technology, 1980, 102, pp. 269–279)
(The American Society of Mechanical Engineers (ASME), 1981) -
Flow Stresses of Prestrained Annealed OFHC Copper and SAE 1018 Steel
(The American Society of Mechanical Engineers (ASME), 1981)The tensile properties of annealed OFHC copper and SAE 1018 steel drawn to various prestrains up to ln A0 /A ≅ 1.5 were evaluated. It was found that the resulting Bridgman corrected curves ... -
A Plastic Fracture Instability Analysis of Wall Breakthrough in a Circumferentially Cracked Pipe Subjected to Bending Loads
(The American Society of Mechanical Engineers (ASME), 1981)A method of analyzing internal surface circumferential cracks in ductile reactor piping is presented. The method utilizes an alternate but equivalent definition of the J-integral based on nonlinear ... -
Dynamic Analysis of a Torsion Test Specimen Including Heat Conduction and Plastic Flow
(The American Society of Mechanical Engineers (ASME), 1981)This paper presents an analysis of a copper torsion test specimen exhibiting a thermal softening instability at a high strain rate. A consititutive relationship derived from test data includes ... -
Strong Tough HSLA Steels Via Processing and Heat Treating of Cu-Ni-Cb and Cu-Ti-B Compositions
(The American Society of Mechanical Engineers (ASME), 1981)The paper deals with the development of control-rolled Cu-Ni-Cb HSLA steels with increased section capability for low-temperature environments and Cu-Ti-B HSLA steels for general structural ... -
Endochronic Description of Cyclic Hardening Behavior for Metallic Materials
(The American Society of Mechanical Engineers (ASME), 1981)The cyclic hardening behavior of metallic materials at a prescribed constant plastic strain rate is investigated. The development is within the framework of the endochronic theory of viscoplasticity. ... -
A Statistically Based Investigation of the Environmental and Cyclic Stress Effects on Fretting Fatigue
(The American Society of Mechanical Engineers (ASME), 1981)A completely randomized factorial experiment was conducted to investigate the environmental and cyclic stress effects on the fretting fatigue behavior of 7075-T6 aluminum alloy. Fretting fatigue ... -
Fracture and Wear of Diamond Cutting Tools
(The American Society of Mechanical Engineers (ASME), 1981)This paper describes the performance of diamond cutting tools during high speed precision machining. Experimental data collected from a very large sample size showed that the tool life varied ... -
Discussion: “A Critical Analysis of Crack Growth in Creep” (Radhakrishnan, V. M., and McEvily, A. J., ASME J. Eng. Mater. Technol., 102, pp. 200–206)
(The American Society of Mechanical Engineers (ASME), 1981) -
The Effects of Periodic High Loads on Fretting Fatigue
(The American Society of Mechanical Engineers (ASME), 1981)Fretting fatigue tests have been conducted on 7075-T7351 aluminum alloy coupons with fretting pads of the same material. Three different stress ratios were used, the otherwise constant amplitude ... -
A New Parameter for Characterizing Corrosion Fatigue Crack Growth
(The American Society of Mechanical Engineers (ASME), 1981)The role of mechanical factors, such as ΔK, R, and K̇ (loading rate), and its significance on corrosion fatigue crack growth acceleration were discussed in terms of crack tip strain rate ... -
Strength of the Surface Layer of Mild Steel
(The American Society of Mechanical Engineers (ASME), 1981)The load-strain curves of thin-walled hollow cylinders of mild steel under compression, bending or torsion and rectangular cross-sectional beams with small height under bending deviate from the ... -
A State Variable Analysis of Inelastic Deformation of Thin Walled Tubes
(The American Society of Mechanical Engineers (ASME), 1981)This paper presents the results of inelastic analysis performed to calculate the deformation of a thin-walled tube subjected to a variety of loadings at elevated temperatures. A state variable ... -
Plastic Deformation Behavior of Mild Steel Along Orthogonal Trilinear Strain Trajectories in Three-Dimensional Vector Space of Strain Deviator
(The American Society of Mechanical Engineers (ASME), 1981)An experiment was performed on the plastic deformation of mild steel S15C by applying combined loads to thin-walled tubular specimens so that the deformation developed along orthogonal trilinear ... -
A Phenomenological Model for Transient Deformation Based on State Variables
(The American Society of Mechanical Engineers (ASME), 1981)The state variable theory of Hart, while providing a unified description of plasticity-dominated deformation, exhibits deficiencies when it is applied to transient deformation phenomena at stresses ... -
Evaluation of Radiation Damage in Reactor Pressure Vessel Steel by Elastic-Plastic Fracture Mechanics
(The American Society of Mechanical Engineers (ASME), 1981)Elastic-plastic toughness characterization of SA533B nuclear pressure vessel steel is described in terms of the J integral approach. A simple test procedure has been proposed from which the JIC ... -
Complete Numerical Solution of the Axisymmetrical Deep-Drawing Problem
(The American Society of Mechanical Engineers (ASME), 1981)The present study introduces a finite difference method to obtain the complete numerical solution of the axisymmetrical deep-drawing of a circular blank. The theory includes nonlinear strain-hardening, ... -
A Damage Accumulation Model for Fatigue Crack Propagation
(The American Society of Mechanical Engineers (ASME), 1981)The fatigue crack propagation rate is investigated on the basis of a dislocation multiplication model which was used previously in evaluation of the fatigue life up to crack initiation. The ... -
A Review of the Recent Literature on the Unlubricated Sliding Wear of Dissimilar Metals
(The American Society of Mechanical Engineers (ASME), 1981)A survey is presented of recent theories of the wear which occurs when dissimilar unlubricated metals slide on one another. Such sliding wear is not only of practical importance, but is also ...