Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2721-2740 of 3257
-
Interaction Diagram for Time Dependent Fatigue
(The American Society of Mechanical Engineers (ASME), 1983)Interaction of fatigue with corrosion and creep has been analyzed through a parameter [Fi ] introduced at the crack propagation stage. Assuming the effect of corrosion and creep to become ... -
An Evaluation of Anisotropic Effective Stress-Strain Criteria for the Biaxial Yield and Flow of 2024 Aluminum Tubes
(The American Society of Mechanical Engineers (ASME), 1983)2024 aluminum tubes, heat treated to a T6 and T8 temper, were tested in combinations of tension-internal pressure and tension-torsion loading. Yield loci and flow behavior were determined for ... -
Fatigue Design, 2nd Edition
(The American Society of Mechanical Engineers (ASME), 1983) -
Time Dependence in Biaxial Yield of Type 316 Stainless Steel at Room Temperature
(The American Society of Mechanical Engineers (ASME), 1983)This paper describes two biaxial experiments which investigated time and rate effects in the yield and deformation behavior of type 316 stainless steel at room temperature. The first experiment ... -
Erratum: “An Experimental Investigation Into the Plastic Flow and Strain Hardening of Mild Steel Under Proportional and Abruptly Changing Deformation Paths at a Controlled Rate” (Journal of Engineering Materials and Technology, 1983, 105, pp. 147–154)
(The American Society of Mechanical Engineers (ASME), 1983) -
Effects of Prior Creep on Subsequent Plasticity of Type 316 Stainless Steel at Elevated Temperature
(The American Society of Mechanical Engineers (ASME), 1983)History effects of prior creep on subsequent plasticity were studied for type 316 stainless steel at 600°C under combined torsion and tension. Following each of three different amounts of ... -
Erratum: “Fatigue Life Prediction for Complex Load Versus Time Histories” (Journal of Engineering Materials and Technology, 1983, 105, pp. 206–214)
(The American Society of Mechanical Engineers (ASME), 1983) -
Benchmark Cyclic Plastic Notch Strain Measurements
(The American Society of Mechanical Engineers (ASME), 1983)Plastic strains at the roots of notched specimens of Inconel 718 subjected to tension-compression cycling at 650°C are reported. These strains were measured with a laser-based technique over ... -
Statistical Evaluation of Some Hot Rolling Theories
(The American Society of Mechanical Engineers (ASME), 1982)The accuracy and precision of four mathematial models of varying complexity are evaluated by comparing their predictions to experimental data generated in carefully controlled laboratory experiments ... -
The Rolling of Very Thin Sheets
(The American Society of Mechanical Engineers (ASME), 1982)Thin strip specimens were reduced to foil by passing them repeatedly between the rolls of a two-high mill at low speeds. Narrow specimens were tested to avoid complications caused by roll ... -
Relationship Between Some Physico-Mechanical Properties and Numerical Indexes of Graphite Shape in Compacted-Vermicular Graphite Cast Irons
(The American Society of Mechanical Engineers (ASME), 1982)The main purpose of this paper is to present some data on the mechanical and physical properties of compacted-vermicular graphite cast iron and to give a reasonable interpretation to the ... -
Steady and Transient Creep Behavior Based on Unified Constitutive Equations
(The American Society of Mechanical Engineers (ASME), 1982)A set of constitutive equations, which has been used to describe a variety of quasi-static and dynamic viscoplastic phenomena, are applied to creep problems. Simulations of steady and transient ... -
Kevlar Composites
(The American Society of Mechanical Engineers (ASME), 1982) -
Discussion of a New Experimental Method in Measuring Fracture Toughness Initiation at High Loading Rates by Stress Waves
(The American Society of Mechanical Engineers (ASME), 1982)An experimental method is described for measuring the fracture initiation properties of metals and alloys over a wide range of loading rates, which can cover over six orders of magnitude in ... -
Composite Materials in the Automobile Industry
(The American Society of Mechanical Engineers (ASME), 1982) -
A Study of Strain and Strain-Rate Dependent Properties of a Superplastic Zn-Al Alloy Under Biaxial Stresses
(The American Society of Mechanical Engineers (ASME), 1982)A superplastic Zn-Al alloy in sheet form is formed into a bulge over a circular hole by pneumatic pressure. The geometry, the stress, the strain, and the strain-rate are determined at various ... -
A Nonlinear Elastic Model for Isotropic Materials With Different Behavior in Tension and Compression
(The American Society of Mechanical Engineers (ASME), 1982)This note presents a model suitable for the mechanical characterization of isotropic materials with different behavior in tension and compression. The model has been derived from the nonlinear ... -
Constitutive Equations for the Rate-Dependent Deformation of Metals at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1982)Approximate constitutive equations are proposed for use in the analysis of the rate-dependent deformation of metals at temperatures in excess of a homologous temperature of 0.5. The constitutive ... -
Constitutive Equations Study in Biaxial Stress Experiments
(The American Society of Mechanical Engineers (ASME), 1982)An experimental study of high temperature creep constitutive equations is reported. The experiments are performed in uniaxial and biaxial (tension-torsion) state of stress. Stress drop experiments ... -
A Simplified Approach to the Effect of Specimen Size on the Creep Rupture of Cross Weld Samples
(The American Society of Mechanical Engineers (ASME), 1982)Various methods are available to assess the performance of welded joints under creep conditions. One approach uses the creep rupture testing of cross weld geometries in uniaxial tension. This ...