Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2701-2720 of 3257
-
Multilevel Strain Controlled Fatigue on a Type 304 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1983)A series of cumulative damage strain-controlled fatigue tests at 20°C has been carried out on a Type 304 stainless steel with two, three, and five strain levels, both in an increasing ... -
Constraint Effects on the Prediction of Fatigue Life of Surface Flaws
(The American Society of Mechanical Engineers (ASME), 1983)The effects of the variation of stress field triaxiality on the prediction of the fatigue growth of semielliptic surface flaws are investigated. The concepts of crack closure are used in a ... -
Dynamic Crush of Tubes
(The American Society of Mechanical Engineers (ASME), 1983)The initial collapse load and the energy absorbed during collapse were measured for brass tubing over a range of compression rates from ∼ 2 × 10−4 m/s to ∼ 12 m/s using two different ... -
Fatigue of Autofrettaged Thick Tubes: Effect of Thermal Shock, Electropolishing, and Tempering
(The American Society of Mechanical Engineers (ASME), 1983)Thick tubes of 32.3 mm (1.27 in.) ID and wall ratio of 2.5 for SAE 4333 steel were subjected to fatigue testing after the following treatments: normal autofrettage followed by thermal shock; ... -
Stress-Strain Properties of Tough-Pitch Copper After Multi-Pass Drawing and Extruding
(The American Society of Mechanical Engineers (ASME), 1983)Tough-pitch copper was drawn and extruded in multi-pass operations to effective strains of 1.53 or area reductions of 80 percent. It appears that residual stresses and mean pressure did not ... -
A Statistical Approach to Nondestructive Testing of Laser Welds
(The American Society of Mechanical Engineers (ASME), 1983)A statistical analysis of the data obtained from a relatively new nondestructive technique for laser welding is presented. The technique is one in which information relating to the quality of ... -
Fatigue Life Prediction for Complex Load Versus Time Histories
(The American Society of Mechanical Engineers (ASME), 1983)Fatigue life prediction for complex load versus time histories is considered from the viewpoint of separating the history into discrete events, or cycles, which may then be used with constant ... -
Yield Phenomena of Post Biaxially Strained Metals
(The American Society of Mechanical Engineers (ASME), 1983)In sequential of multistep forming operations, the material which has already undergone permanent deformation is expected to behave differently in each stage of deformation than the as-received ... -
Analysis of Flexure Strength Data of Ceramics
(The American Society of Mechanical Engineers (ASME), 1983)A method to obtain the two and three Weibull parameters from the statistical strength distribution of ceramics, when either surface flaws or volumetric flaws govern fracture, is outlined. The ... -
An Experimental Study on the Cold Rolling of Strips
(The American Society of Mechanical Engineers (ASME), 1983)The power consumption and the orthogonal strains were measured during cold rolling of thin strips of aluminum, stainless steel, mild steel and bronze, under lubricated condition and through ... -
Incremental Failure of an Expansion Joint During Combined Pressure and Expansion Loading
(The American Society of Mechanical Engineers (ASME), 1983)Incremental failure was observed when two different loading conditions, pressure and expansion, were applied alternatively to an expansion joint. Neither of the conditions was capable independently ... -
Erratum: “Behavior of Soft Spheres During Impact by High-Speed Photography” (Journal of Engineering Materials and Technology, 1983, 105, pp. 67–73)
(The American Society of Mechanical Engineers (ASME), 1983) -
An Anisotropic Generalization of the Bridgman Analysis of Tensile Necking
(The American Society of Mechanical Engineers (ASME), 1983)Tensile necking in anisotropic bars is analyzed in the spirit of P. W. Bridgman’s treatment of the isotropic case. Anisotropic plastic flow causes an initially axisymmetric bar to develop an ... -
The Effects of Hold Period on the Fatigue Crack Growth Rate of 2 1/4 Cr-1Mo Steel at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1983)The effects of various loading wave forms on the fatigue crack growth rate of 2 1/4 Cr-1Mo steel at 482 and 538°C tested in air have been determined. Scanning electron fractography was ... -
An Experimental Investigation Into the Plastic Flow and Strain Hardening of Mild Steel Under Proportional and Abruptly Changing Deformation Paths at a Controlled Rate
(The American Society of Mechanical Engineers (ASME), 1983)Tension-torsion tests are reported on thin-walled tubes up to strains of the order of five percent. Attention was given to the question of whether, as has been suggested, in the continued ... -
Punch Press Monitoring with Acoustic Emission (AE) Part II: Effects of Process Variables
(The American Society of Mechanical Engineers (ASME), 1983)In a previous paper, the acoustic emission (AE) signal emitted from a Minster1 #3 punch press was completely characterized and effects of stock hardness were examined. The AE signal emitted ... -
Analysis of an Idealized Directionally Solidified FCC Material
(The American Society of Mechanical Engineers (ASME), 1983)Directionally solidified materials are being increasingly used in aircraft engines. These alloys are anisotropic due to the well aligned crystalline structure with additional considerations including ... -
An Evaluation of the Compact Shear Specimen for Mixed Mode Fracture Studies
(The American Society of Mechanical Engineers (ASME), 1983)A compact shear specimen configuration, consisting of three legs with the outer two loaded axially in a direction opposite to the inner one, has been used for several mixed-mode fracture ... -
Toughness of Cr-Mo-V Steels for Steam Turbine Rotors
(The American Society of Mechanical Engineers (ASME), 1983)Cr-Mo-V steels are used extensively as the rotor material in the High Pressure and Intermediate Pressure Sections of modern steam turbines. The toughness of these rotors has a major influence ... -
Punch Press Monitoring with Acoustic Emission (AE) Part I: Signal Characterization and Stock Hardness Effects
(The American Society of Mechanical Engineers (ASME), 1983)As an integral part of the punch press monitoring research program, the Acoustic Emission (AE) signal emitted from a Minster1 #3 punch press is completely characterized in terms of signal ...