Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2621-2640 of 3257
-
An Analytical Rolling Model Including Through Thickness Shear Stress Distributions
(The American Society of Mechanical Engineers (ASME), 1984)An extension of the slab method of analysis as applied to rolling is presented. The von Mises yield criterion, including shear stresses, is written in terms of the frictional boundary condition ... -
The Fatigue Behavior of Nickel, Monel, and Selected Superalloys, Tested in Liquid Mercury and Air; A Comparison
(The American Society of Mechanical Engineers (ASME), 1984)The fatigue lifetimes and fractography were compared for nickel and typical nickel base alloys of the Monel, Inconel, and Incoloy series, tested at room temperature in alternating tension in ... -
Failure of Materials in Mechanical Design
(The American Society of Mechanical Engineers (ASME), 1984) -
Redundant Deformation Factor Evaluation Through the Hardness Profile Method in Round Section Bar Drawing
(The American Society of Mechanical Engineers (ASME), 1984)The increase in strength of bars caused by drawing is associated to the average deformation (ε ) imparted to the material by processing. This paper discusses the hardness profile method for ... -
Surface Integrity in Machining Solution-Treated and Aged 2024-Aluminum Alloy, Using Natural and Controlled Contact Length Tools. Part I—Unlubricated Conditions
(The American Society of Mechanical Engineers (ASME), 1984)The effects of cutting speed, chip-tool contact length and tool surface finish on the surface integrity of a solution-treated and aged 2024-Aluminum alloy, that is machined under dry, orthogonal ... -
Study of Friction in Cold Strip Rolling
(The American Society of Mechanical Engineers (ASME), 1984)Experiments were conducted to measure the effects of roll pressure and roll rpm on the magnitude and variation of the coefficient of friction in the roll gap in cold strip rolling. Two ... -
Process Modeling of Orthogonal Cutting by the Rigid-Plastic Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1984)A numerical modeling method for plane strain orthogonal cutting in steady state is developed on the basis of the rigid-plastic finite element method. The methods for determining the material ... -
Surface Integrity in Machining Solution-Treated and Aged 2024-Aluminum Alloy, Using Natural and Controlled Contact Length Tools. Part II—Lubricated Conditions
(The American Society of Mechanical Engineers (ASME), 1984)The effects of cutting speed, chip-tool contact length, and tool surface finish on the surface integrity of solution-treated and aged 2024-aluminum alloy, that is machined under lubricated ... -
Gross Crack Initiation and Propagation in Brittle Thin Solid and Annular Disks Subjected to Impact Loading
(The American Society of Mechanical Engineers (ASME), 1984)This paper derives from a study of grinding wheel break-up behavior due to impact. The impact fracture characteristics of circular disks of plaster of Paris with a concentric central hole were ... -
On the Microstructural Basis of Cleavage Fracture Initiation in Ferritic and Bainitic Steels
(The American Society of Mechanical Engineers (ASME), 1984)The microstructural basis of the critical tensile stress criterion of cleavage fracture is discussed. It is shown that cleavage can be carbide induced in bainitic steels as well as in ferritic ... -
Correction of Distortions in Dynamic Crush Test Data Due to Load Cell Inertia Effects
(The American Society of Mechanical Engineers (ASME), 1984)The application of deconvolution techniques to the results obtained in the dynamic collapse of tubes in axial compression is described. It is shown that low pass filtering techniques are not ... -
Estimates of the J-Integral for Elastic-Plastic Specimens in Large Scale Yielding
(The American Society of Mechanical Engineers (ASME), 1984)A generalization of the area under the load-deflection curve method for estimating the J-integral in cracked elastic-plastic specimens in large scale yielding is proposed. The results of this ... -
Erratum: “An Analytical Rolling Model Including Through Thickness Shear Stress Distributions” (Journal of Engineering Materials and Technology, 1984, 106, pp. 1–8)
(The American Society of Mechanical Engineers (ASME), 1984) -
Specialty Steels & Hard Materials
(The American Society of Mechanical Engineers (ASME), 1984) -
In-Process Tool Fracture Detection
(The American Society of Mechanical Engineers (ASME), 1984)This paper investigates the feasibility of using acoustic emission (AE) signal analysis for the detection of the breakage as well as the chipping of a cutting tool during machining. Experiments ... -
Measurement of Contact Pressure in Metal Forming by Pressure Sensitive Film
(The American Society of Mechanical Engineers (ASME), 1984)A simple method is presented for measuring the distribution of tool contact pressure in metal forming by using a pressure sensitive film which detects the contact pressure from the change in ... -
The Effects of Plate Stress-Strain Behavior and Pipemaking Variables on the Yield Strength of Large-Diameter DSAW Line Pipe
(The American Society of Mechanical Engineers (ASME), 1984)Recent stringent specifications for large-diameter double-submerged-arc-welded gas-transmission line pipe include requirements that limit the range of allowable pipe yield strengths instead of the ... -
High Carbon Steel Microcracking Control During Hardening
(The American Society of Mechanical Engineers (ASME), 1984)When high carbon, low alloy steels, such as AISI 52100, are conventionally quenched or marquenched from an austenitizing temperature that dissolves all of the carbon in the austenite, many of ... -
Investigation of the One-Dimensional Endochronic Constitutive Equation for Metals by the Rivlin Test
(The American Society of Mechanical Engineers (ASME), 1984)Two sets of experiments with and without strain cycling have been carried out to test the validity of an equation derived from the improved theory of endochronic plasticity. It has been found ... -
The Simulation of Sliding Wear by Cyclic Plastic Deformation Under Combined Stresses
(The American Society of Mechanical Engineers (ASME), 1984)A mechanical test which is believed to simulate the conditions occurring in sliding wear is described. It involves the cyclic plastic deformation of metals under combined compression and shear. ...