Journal of Engineering Materials and Technology: Recent submissions
Now showing items 2601-2620 of 3257
-
An Investigation of the Effects of Grain Size and Hardness in Temper-Embrittled 2 1/4 Cr-1 Mo Steel
(The American Society of Mechanical Engineers (ASME), 1984)Measurements of FATT as a function of hardness, grain size, and fracture surface impurity concentration were made on a 2 1/4 Cr-1 Mo steel doped with Mn + Si + P in an effort to devise ... -
Wear Studies on TiC Coated Cemented Titanium Carbide Tools
(The American Society of Mechanical Engineers (ASME), 1984)Extensive and rigorous wear tests involving the failure criterion were carried out initially on (i) TiC coated and (ii) uncoated cemented tungsten carbide, and (iii) cemented titanium carbide ... -
Preface
(The American Society of Mechanical Engineers (ASME), 1984) -
Evaluation of a New High Strength Austenitic Alloy for Generator Retaining Rings
(The American Society of Mechanical Engineers (ASME), 1984)A new high strength, nonmagnetic, iron-base alloy has been developed for large retaining ring application. This alloy is based on the development efforts recently completed in a previous ... -
Statistics of Crack Growth of a Superalloy Under Sustained Load
(The American Society of Mechanical Engineers (ASME), 1984)A statistically-formulated fracture mechanics model for crack growth under sustained load is used to analyze crack growth data from 23 compact tension specimens of IN100, a turbojet engine disk ... -
A Modeling Study of Metal Cutting With Abrasive Waterjets
(The American Society of Mechanical Engineers (ASME), 1984)An experimental and theoretical investigation was conducted to study the cutting of ductile metals with high-velocity abrasive jets. The investigation involved experimental cutting tests, visualization ... -
Materials Testing for Cold Forging
(The American Society of Mechanical Engineers (ASME), 1984)The article describes a series of experiments, and some associated theoretical work, which should assist in assessing the suitability of certain steels designated for cold forging operations. The ... -
Fracture Toughness Evaluation of the Heterogeneous Bond Region in HT80 Steel Weldments
(The American Society of Mechanical Engineers (ASME), 1984)Fracture toughness tests of specimens in which the crack fronts consist of the weld metal region, the HAZ, and the base metal region have been carried out. It seems that, even in the case ... -
Fatigue Crack Retardation of Low Carbon Steel in Saltwater
(The American Society of Mechanical Engineers (ASME), 1984)The crack propagation behavior following the application of a single tensile overload in 3 percent saltwater was examined using a low carbon steel, which has a considerably lower static strength ... -
Predictions of the Stress Intensity Factor for an Internal Circumferential Crack at a Butt-Weld Between Cylinders Using the Plane Strain Solution
(The American Society of Mechanical Engineers (ASME), 1984)It is assumed that the axial bending stresses which arise from this type of weld have a linear distribution. From these stresses, axisymmetric solutions in the literature enable the stress ... -
Constant and Variable Amplitude Fatigue Behavior of Five Cast Steels at Room Temperature and −45°C
(The American Society of Mechanical Engineers (ASME), 1984)A comprehensive fatigue program was undertaken at room temperature and −45°C (−50°F) for five representative carbon or low alloy cast steels. Constant amplitude low and high cycle axial ... -
Intermediate Temperature, Low-Cycle Fatigue Behavior of Coated and Uncoated Nickel Base Superalloys in Air and Corrosive Sulfate Environments
(The American Society of Mechanical Engineers (ASME), 1984)Low temperature hot corrosion effects on the low cycle fatigue (LCF) life and fracture morphology of a Udimet 720 alloy and the effectiveness of a protective coating in minimizing life degradation ... -
Creep-Rupture Behavior of Six Candidate Stirling Engine Superalloys Tested in Air
(The American Society of Mechanical Engineers (ASME), 1984)The creep-rupture behavior of six candidate Stirling engine iron-base superalloys was determined in air. The alloys included four wrought alloys (A-286, Alloy 800H, N-155, and 19-9DL) and two ... -
Geometrically Nonlinear Analysis of Adhesively Bonded Joints
(The American Society of Mechanical Engineers (ASME), 1984)A geometrically nonlinear finite-element analysis of cohesive failure in typical joints is presented. Cracked-lap-shear joints were chosen for analysis. Results obtained from linear and nonlinear ... -
The Nature of Chip Formation in Orthogonal Machining
(The American Society of Mechanical Engineers (ASME), 1984)Orthogonal machining experiments were conducted at the cutting speed of 8.5 × 10−2 cm/s with 6061-T6 aluminum, 4340 steel and Ti-6Al-4V titanium to measure strain distributions in the ... -
The Tensile Fracture Characteristics of Nickel, Monel, and Selected Superalloys Broken in Liquid Mercury
(The American Society of Mechanical Engineers (ASME), 1984)An investigation was performed, using the slow strain-rate tensile test technique, to determine whether nickel and typical nickel base alloys were susceptible to embrittlement by liquid mercury ... -
On the Thickness Effect of Axisymmetric Deformation of Sheet Metals
(The American Society of Mechanical Engineers (ASME), 1984)In the present investigation, we have studied the influence of sheet thickness on the limiting strain, i.e., forming limit, of a mild steel by punch stretching experiments. Our results show ... -
Prediction of Fatigue Threshold of Notched Components
(The American Society of Mechanical Engineers (ASME), 1984)A consistent method is proposed to predict significant properties concerning the notch fatigue threshold from three experimental data: the fatigue limit of smooth specimens, the threshold stress ... -
JIc Determination of Five Cast Steels at Room Temperature and −45°C (−50°F)
(The American Society of Mechanical Engineers (ASME), 1984)JIc tests using the multiple specimen procedure described in ASTM standard E813 were conducted at room temperature and −45°C (−50°F) with five common carbon or low alloy cast steels, ... -
Validation of Compact-Specimen Crack-Arrest Data
(The American Society of Mechanical Engineers (ASME), 1984)