Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1641-1660 of 3257
-
A Method for Damage Evaluation of Laminated Composite Materials by Using Model Updating Techniques in Dynamics
(The American Society of Mechanical Engineers (ASME), 1998)A method for damage identification in composite materials by model updating techniques in dynamics has been proposed. The modeling and the general aspects of the damage in composite materials ... -
Tensile and Bending Behavior of Sintered Alloys: Experimental Results and Modeling
(The American Society of Mechanical Engineers (ASME), 1998)Sintered materials show a different stress-strain behavior when subjected to tensile or compressive loading, the response to compression being characterized by a higher elastic modulus, yield ... -
Strain Space Formulation of the Armstrong-Frederick Family of Plasticity Models
(The American Society of Mechanical Engineers (ASME), 1998)Strain space based plasticity models have certain advantages in theoretical development and numerical implementation. Previous efforts have been made to formulate cyclic plasticity models in strain ... -
Applicability of Neuber’s Rule to the Analysis of Stress and Strain Concentration Under Creep Conditions
(The American Society of Mechanical Engineers (ASME), 1998)A differential form of Neuber’s rule, originally proposed by M. Chaudonneret, has been formulated for a generic viscoplastic notch problem, making extensive use of suitably normalised stress, ... -
Oxidation Induced Stress-Rupture of Fiber Bundles
(The American Society of Mechanical Engineers (ASME), 1998)The effect of oxidation on the stress-rupture behavior of fiber bundles was modeled. It is shown that oxidation-induced fiber strength degradation results in the delayed failure of the associated ... -
Application of the Taylor Polycrystal Plasticity Model to Complex Deformation Experiments
(The American Society of Mechanical Engineers (ASME), 1998)The extended Taylor assumption of uniform deformation gradient among grains was applied in 3-D polycrystal plasticity simulations for complex loading paths at finite strain for OFHC Cu using the ... -
An Experimental Study of Ratchetting During Indentation of 316L Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1998)This paper deals with fatigue problems of 316L stainless-steel surgical structures used in the correction of pelvic obliquity. The structures consist of implants, milled rods, and screws. SEM ... -
Unified Constitutive Equations of Foam Materials
(The American Society of Mechanical Engineers (ASME), 1998)A unified constitutive equation with the effect of compression strain rate, tension strain, and shear strain for foam materials with very low Poisson’s ratio has been developed. The mathematical ... -
Investigation of Localized Deformation in NiAl Single Crystals
(The American Society of Mechanical Engineers (ASME), 1998)Deformation of NiAl single crystals was studied using finite element analysis to investigate the modes of localized deformation. Constitutive parameters and hardening characteristics of the active ... -
Modeling of High Homologous Temperature Deformation Behaviour Using the Viscoplasticity Theory Based on Overstress (VBO): Part III—A Simplified Model
(The American Society of Mechanical Engineers (ASME), 1998)A simplified version of the Viscoplasticity Theory Based on Overstress (VBO) is applied to modeling of Alloy 800H at homologous temperatures between 0.6 and 0.8 The present formulation is ... -
Mechanistic Prediction of Fracture Processes in Ferritic Steel Welds Within the Transition Temperature Regime
(The American Society of Mechanical Engineers (ASME), 1998)This work examines the fracture behavior of ferritic steel welds in the transition temperature regime, where failure can occur either by ductile tearing or cleavage fracture. A computational and ... -
Prediction of Extent of Heat Affected Zone in Laser Grooving of Unidirectional Fiber-Reinforced Plastics
(The American Society of Mechanical Engineers (ASME), 1998)Laser has been widely used in various industrial applications including machining. However, in shaping operation of composite material after curing, thermal damage associated with laser energy can ... -
On the Chemo-Mechanical Polishing (CMP) of Si3N4 Bearing Balls With Water Based CeO2 Slurry
(The American Society of Mechanical Engineers (ASME), 1998)Among various abrasives investigated for the chemo-mechanical polishing (CMP) of Si3 N4 balls (Jiang, 1998), cerium oxide (CeO2 ) was found to be the most effective polishing medium (even ... -
Numerical Simulation of Residual Stresses Caused by Quenching Process in Aluminium Gas Cylinders
(The American Society of Mechanical Engineers (ASME), 1998)Residual stresses introduced during quenching process in aluminium gas cylinders contribute to the development of cracks. This may result in leakage or fracture of the cylinders. Finite element ... -
Strength Prediction of RTM Single-Lap Joints With Transverse Stitching
(The American Society of Mechanical Engineers (ASME), 1998)It was experimentally shown that transverse stitching can provide an over 20 percent improvement in the strength of composite single-lap joints manufactured using the Resin Transfer Moulding (RTM) ... -
Automatic Simulation of a Sequence of Hot-Former Forging Processes by a Rigid-Thermoviscoplastic Finite Element Method
(The American Society of Mechanical Engineers (ASME), 1998)A fully automatic forging simulation technique in hot-former forging is presented in this paper. A rigid-thermoviscoplastic finite element method is employed together with automatic simulation ... -
Modeling of GMA Weld Pools With Consideration of Droplet Impact
(The American Society of Mechanical Engineers (ASME), 1998)A three-dimensional weld pool model has been developed to study the fluid flow and heat transfer process during gas metal arc (GMA) welding. Both droplet heat content and impact force were ... -
Viscoplastic Collapse of Thin-Walled Tubes Under Cyclic Bending
(The American Society of Mechanical Engineers (ASME), 1998)This paper presents the experimental result on the response and stability of thin-walled tubes subjected to cyclic bending with different curvature-rates. The curvature-ovalization measurement ... -
Study on the Thermo-Elastic-Plastic Cutting Model for 3-D Tool with Chip Breaker
(The American Society of Mechanical Engineers (ASME), 1998)This paper used large deformation finite element theory, updated Lagrangian formulation, finite difference method, and incremental theory to develop a three-dimensional thermo-elastic-plastic simulation ... -
Cyclic Fatigue Experiments and Analysis of Silicon Nitrides—Stepwise Loading
(The American Society of Mechanical Engineers (ASME), 1998)Rotating beam fatigue test has been performed at room temperature for two types of advanced hot-pressed silicon nitrides. The test completion modes consist of fast fracture, fatigue fracture, ...