Journal of Engineering Materials and Technology: Recent submissions
Now showing items 1621-1640 of 3257
-
A Simulation Procedure for Panel Age Forming
(The American Society of Mechanical Engineers (ASME), 1998)A method of simulating the age forming of initially flat panels is proposed. It conceptually divides the process into three phases (loading, aging, and unloading) and simulates each phase ... -
Measuring Strain Distribution During Mesoscopic Domain Reorientation in a Ferroelectric Material
(The American Society of Mechanical Engineers (ASME), 1998)In this paper, we present the results of an experimental study focused on understanding the strain concentrations arising due to nonlinear phenomena associated with polarization switching. A moire ... -
Rate Data and Material Model Parameter Estimation
(The American Society of Mechanical Engineers (ASME), 1998)Traditionally stress-strain data are used to estimate material parameters in viscoplastic material models. Since the models exist in rate form, they must be integrated in time for the duration ... -
A Consistent Criterion for Diffuse Necking in Sheet Metals Using Hill’s 1979 Yield Surface
(The American Society of Mechanical Engineers (ASME), 1998)A review of some existing criteria for diffuse necking in sheet metals is given and their limitations are discussed. The introduction into production of new sheet materials whose plastic ... -
Phase Transformation Temperatures of an Ultra-Low Carbon Steel
(The American Society of Mechanical Engineers (ASME), 1998)An ultra-low carbon steel is studied and the temperatures at which the austenite to ferrite transformations begin and are complete are determined. The methods of measurements of the temperatures ... -
An Inelastic Constitutive Equation of Fiber Reinforced Plastic Laminates
(The American Society of Mechanical Engineers (ASME), 1998)A Constitutive model for describing the time dependent inelastic deformation of unidirectional and symmetric angle-ply CFRP (Carbon Fiber Reinforced Plastics) laminates is developed. The kinematic ... -
The Single Slice Method for Measurement of Axisymmetric Residual Stresses in Solid Rods or Hollow Cylinders in the Region of Plane Strain
(The American Society of Mechanical Engineers (ASME), 1998)A new method is presented for the measurement of axisymmetric residual stresses in a solid rod or hollow cylinder in the region which is in a state of plane strain. The experimental procedure ... -
An Investigation of Thin-Film Coating/Substrate Systems by Nanoindentation
(The American Society of Mechanical Engineers (ASME), 1998)The indentation load-displacement behavior of three material systems tested with a Berkovich indenter has been examined. The materials studied were the substrate materials—silicon and polycarbonate, ... -
Easy-to-Compute Tensors With Symmetric Inverse Approximating Hencky Finite Strain and Its Rate
(The American Society of Mechanical Engineers (ASME), 1998)It is shown that there exist approximations of the Hencky (logarithmic) finite strain tensor of various degrees of accuracy, having the following characteristics: (1) The tensors are close enough ... -
Damage Accumulation Mechanisms in Thermal Barrier Coatings
(The American Society of Mechanical Engineers (ASME), 1998)Progressive damage evolution leading to spallation was investigated in Electron Beam—Plasma Vapor Deposition (EB-PVD) partially stabilized zirconia thermal barrier coating (TBC) applied to Nickel-based ... -
A Three-Dimensional Network Model for a Low Density Fibrous Composite
(The American Society of Mechanical Engineers (ASME), 1998)A procedure is described that predicts the mechanical behavior of a fibrous material by generating and analyzing finite element models of its three-dimensional microstructure. The approach is ... -
Inelastic Response of Off-Axis MMC Lamina
(The American Society of Mechanical Engineers (ASME), 1998)Damage evolution and failure characteristics were investigated for a 10 deg off-axis SiC/It unidirectional metal matrix composite (MMC) lamina subjected to monotonic loading. A replica technique ... -
A Finite Element Analysis of the Effect of Hardening Rules on the Indentation Test
(The American Society of Mechanical Engineers (ASME), 1998)Using the Finite Element Method, an analysis is given of the indentation of an elasticplastic half-space by a rigid sphere. In particular, attention is focused on the effect of hardening rules ... -
Evaluation of Creep-Fatigue Life Prediction Methods for Low-Carbon Nitrogen-Added 316 Stainless Steel
(The American Society of Mechanical Engineers (ASME), 1998)Low-carbon, medium-nitrogen 316 stainless steel is a principal candidate for a main structural material of a demonstration fast breeder reactor plant in Japan. A number of long-term creep tests ... -
The Burdened Area as a Structural Indicator of Interface Bonding Strength
(The American Society of Mechanical Engineers (ASME), 1998)In laminate structures, the interface debonding failures usually result from very complex fracture mechanisms which lead to different strengthening approaches. The bonding strength of two dissimilar ... -
The Numbers of Elastic Properties and Failure Parameters for Fiber Composites
(The American Society of Mechanical Engineers (ASME), 1998)It is shown that there is a coordination between the numbers of the elastic properties and the numbers of the failure criteria parameters for aligned fiber composites under certain realistic ... -
Plastic Energy Dissipation Model for Lifetime Prediction of Zirconium and Zircaloy-4 Fatigued at RT and 400°C
(The American Society of Mechanical Engineers (ASME), 1998)Low cycle fatigue properties of zirconium and zircaloy-4 were investigated at RT and 400°C. The microscopic structure was determined using scanning electron microscopy and transmission electron ... -
Analysis of Forming Limits Using the Hill 1993 Yield Criterion
(The American Society of Mechanical Engineers (ASME), 1998)Forming limits of thin sheets are investigated using a yield criterion recently proposed by Hill (1993). This criterion utilizes five independent material parameters, which can be determined from ... -
Elastic Constants of Single Crystal Hastelloy X at Elevated Temperatures
(The American Society of Mechanical Engineers (ASME), 1998)An acoustic time of flight technique is described in detail for measuring the elastic constants of cubic single crystals that allows for the constants to be determined at elevated temperature. ... -
A Constitutive Model for Powder Materials
(The American Society of Mechanical Engineers (ASME), 1998)A new elastic/viscoplastic constitutive model for compaction of power materials has been proposed. The model can be determined from a few conventional compression triaxial tests. In this model ...