Now showing items 3181-3200 of 3450

    • Axial Stretching Oscillation of an 18,000-Ft Vertical Pipe in the Ocean 

      J. S. Chung; A. K. Whitney (The American Society of Mechanical Engineers (ASME), 1983)
      For a long pipe in deep ocean with the equipment attached to its free bottom end, the bottom end oscillation can be amplified near resonance several times the top end oscillation amplitude. ...
    • Rig Jacking on Soft Soil Foundations: Improvements in Safety and Speed by Monitoring Leg Loads 

      P. F. Ansquer; S. A. Antalovsky (The American Society of Mechanical Engineers (ASME), 1983)
      The stability of jack-up rigs with spud-cans, particularly during the jacking-up and preloading operations, has always been critical in soft soil conditions. In the offshore areas opened to ...
    • Nonlinear Dynamic Analysis of Guyed Tower Platforms 

      S. Y. Hanna; A. Mangiavacchi; R. Suhendra (The American Society of Mechanical Engineers (ASME), 1983)
      A method of analysis is presented to predict the nonlinear dynamic behavior of compliant offshore structures, in particular guyed tower platforms. The structural model is analyzed in time domain ...
    • Experimental Study of Hydraulic Fracturing in an Impermeable Material 

      M. B. Rubin (The American Society of Mechanical Engineers (ASME), 1983)
      A laboratory experiment was conducted to study hydraulic fracturing in an impermeable material (PMMA). Quantitative experimental data were obtained to compare with numerical predictions for a ...
    • Determination of In-Situ Stresses From Hydraulically Fractured Spherical Cavities 

      W. E. Warren (The American Society of Mechanical Engineers (ASME), 1983)
      Several problems in analysis can arise in estimating in-situ stresses from standard hydraulic fracturing operations if the borehole is not aligned with one of the principal stress directions. ...
    • Optimized Ejector-Diffuser Design Procedure for Natural Gas Vapor Recovery 

      J. C. Dutton; B. F. Carroll (The American Society of Mechanical Engineers (ASME), 1983)
      A procedure for designing optimized ejector-diffuser systems for recovering natural gas vapor from oil storage tanks is presented. The system utilizes high pressure gas from the separator to ...
    • Design and Operation of a Versatile Pollution Control/Liquid Waste Thermal Destruction System With Maximum Energy Recovery 

      F. Hasselriis (The American Society of Mechanical Engineers (ASME), 1983)
      This paper describes an innovative fume incinerator which supplies all the steam needs of an industrial plant by burning waste liquid fuels, yet is flexible enough to match the instantaneous, ...
    • Direct Coburning of Unprepared Municipal Solid Waste and Sludge 

      M. Dvirka (The American Society of Mechanical Engineers (ASME), 1983)
      The paper describes derivation of data and guidelines for coburning of municipal sludges and unprepared solid waste, giving approximate limits of applicability using direct coburning model with ...
    • Knocking From Valve Hammer in Triplex Pumps 

      S. L. Collier (The American Society of Mechanical Engineers (ASME), 1983)
      This paper investigates valve hammer as opposed to water hammer in triplex pumps, both of which produce knocking under certain distinctly different hydraulic operations. The occurrence of water ...
    • Fracture Analysis of Ceramic Proppants 

      S. R. Swanson; R. A. Cutler (The American Society of Mechanical Engineers (ASME), 1983)
      Small particles (traditionally sand) are mixed with fluid in hydraulic fracturing treatments of petroleum wells to stimulate production. The solid particles, called proppants, are used to prop ...
    • Identification and Rock Failure Characterization in Bit-Tooth Penetration 

      E. I. Umez-Eronini (The American Society of Mechanical Engineers (ASME), 1983)
      Parameter values required in a previous rock model are estimated using the invariant imbedding identification technique applied to a bit-tooth drop test. Sequential data generated during the ...
    • Combined Cycles—Alternative for Process Steam Systems 

      H. L. Harkins (The American Society of Mechanical Engineers (ASME), 1983)
      The state-of-the-art combined cycle system consisting of combustion turbines, heat recovery steam generators, and steam turbine-generator units, offers a high-efficiency method for the production ...
    • Rock Bit Cutter Tooth Design and Analysis 

      G. C. Feng; P. W. Schumacher (The American Society of Mechanical Engineers (ASME), 1983)
      The finite element method was used to analyze the stresses in a rock bit cutter tooth under applied loads. Detailed finite element models were constructed to allow accurate descriptions of the ...
    • Startup and Shakedown of Albany New York Solid Waste Energy Recovery System 

      A. R. Nollet; R. H. Greeley (The American Society of Mechanical Engineers (ASME), 1983)
      This paper describes the Albany New York Solid Waste Energy Recovery System (ANSWERS), which consists of two plants — a City-owned refuse-derived fuel (RDF) plant, and a State-owned boiler plant ...
    • Frictional Pressure Losses for Single-Phase and Two-Phase Flow of Drilling Muds 

      F. A. Elfaghi; J. P. Langlinais; A. T. Bourgoyne; W. R. Holden (The American Society of Mechanical Engineers (ASME), 1983)
      The vertical flow of mud and gas-mud mixtures in long pipes is of interest in the design and operation of subsea well control equipment where long choke lines are required. Heretofore, the ...
    • Energy Losses Related to Automatic Steering of Ships in Waves—Part II: Performance of Controllers Designed to a New Criterion 

      R. E. Reid; B. C. Mears; D. E. Griffin (The American Society of Mechanical Engineers (ASME), 1983)
      Minimization of energy losses associated with the steering control of modern ship types is discussed on the basis of frequency-domain sensitivity analyses and time-domain simulation studies. A ...
    • An Analysis of Chain Forces of a SBS Under Regular Wave Action 

      Yu-Xiu Yu (The American Society of Mechanical Engineers (ASME), 1983)
      Since the first Single Buoy Storage System (SBS) installed in Aquitaine-Tunisia in 1974 [1, 2], many similar systems have been installed. To facilitate oil production in Gulf Bohai, China, a ...
    • Stresses in Multilayered Cables 

      G. A. Costello (The American Society of Mechanical Engineers (ASME), 1983)
      A theory is presented which will predict the stresses in a multilayered cable, subjected to axial, bending and torsional loads. In the axial case, the axial force and axial twisting moment ...
    • Limit Analysis of Ice Sheet Indentation 

      D. G. Karr; S. C. Das (The American Society of Mechanical Engineers (ASME), 1983)
      The methods of plastic limit analysis are used to determine the indentation pressures of a flat rectangular punch on an ice sheet. The ice sheet is idealized as a semi-infinite layer of ...
    • Nonlinear and Hysteretic Twisting Effects in Ocean Cable Laying 

      A. J. Shashaty (The American Society of Mechanical Engineers (ASME), 1983)
      Armored ocean cable unlays under the action of installation tensions and restraining moments applied by the ocean bottom and the ship’s bow sheave. The process of elongation and twist is ...