Journal of Energy Resources Technology: Recent submissions
Now showing items 2881-2900 of 3450
-
Acrylic Plastic Spherical Pressure Hull for 2439 m (8000 ft) Design Depth: Phase I
(The American Society of Mechanical Engineers (ASME), 1987)A program has been initiated to provide the oceanographic community with a manned submersible with panoramic visibility for 2439 m (8000 ft) design depth. The first phase of the program is ... -
Transmission of Solid Particulates Using a Two-Phase Medium
(The American Society of Mechanical Engineers (ASME), 1987)The ability of water to hold solid particulate matter in suspension, together with its fluidity, make it a desirable medium for use in the transportation of solid material in slurry pipelines. ... -
Feasibility Study of Ammonia-Water Vapor Absorption Heat Transformer
(The American Society of Mechanical Engineers (ASME), 1987)Many industrial sectors reject heat to the atmosphere in the form of hot water with a temperature between 40° and 70°C. This low grade heat can be upgraded by using a vapor absorption ... -
Numerical Solution Techniques for Dynamic Analysis of Marine Riser
(The American Society of Mechanical Engineers (ASME), 1987) -
An Analytical Study of Heat and Mass Transfer Within an Oil Sand Bed
(The American Society of Mechanical Engineers (ASME), 1987)The physical processes that occur typically within an oil sand bed are considered when the bed is subjected to a hot gaseous stream. In this study, the extent of fluid volatilization was ... -
Volatilization of Packed Beds of Oil Sand Particles
(The American Society of Mechanical Engineers (ASME), 1987)Based on a quasi-steady system, published experimental data on mass transfer in packed beds of spherical particles at relatively low Reynolds numbers, were employed to estimate the convective ... -
Operating Experience With a Fluidized Bed Test Combustor
(The American Society of Mechanical Engineers (ASME), 1987)This paper presents operating experience with a fluidized bed combustor burning various coals. The primary focus is on the effect of relevant coal properties on combustor performance. Tests were ... -
Analysis of Wood Combustion Based on the First and Second Laws of Thermodynamics
(The American Society of Mechanical Engineers (ASME), 1987)Wood is a highly flexible fuel which can be used in a variety of ways for energy generation. Direct combustion of wood is the oldest method of utilization of this renewable energy source. ... -
Multiphase Flow Field Trials on BP’s Magnus Platform
(The American Society of Mechanical Engineers (ASME), 1987)The trend toward offshore oilfield development schemes which utilize relatively long, large diameter, multiphase flowlines has resulted in a need for better design techniques for such systems. ... -
Optimization of Air-Cooled Condensers
(The American Society of Mechanical Engineers (ASME), 1987)The essential design parameters for determining the optimum configuration of an air-cooled condenser are identified in this paper. For a power plant operating on a Rankine cycle, expressions for ... -
Theoretical Thermal Evaluation of Energy Recovery Incinerators—Part II: Parametric Examination
(The American Society of Mechanical Engineers (ASME), 1987)The thermal characteristics of energy recovery incinerators are examined, both parametrically and, to the extent possible, by direct comparison. A mathematic model is employed, using a computer ... -
Theoretical Thermal Evaluation of Energy Recovery Incinerators—Part I: Modeling
(The American Society of Mechanical Engineers (ASME), 1987)A mathematical model is developed to simulate the thermal characteristics of energy recovery incinerators. This model takes descriptions of the fuel and of the incinerator as inputs then predicts ... -
An Examination of the Interaction Between Oil Sand Fragments in Hot Gaseous Streams
(The American Society of Mechanical Engineers (ASME), 1987)Clusters of preshaped oil sand spherical fragments were subjected to hot steady streams of air at low Reynolds number and constant stream temperature. A wide range of different combinations and ... -
Experimental Studies on Combustion of Cattle Manure in a Fluidized Bed Combustor
(The American Society of Mechanical Engineers (ASME), 1987)Manure from cattle feedlots is a renewable energy source which has the potential of supplementing the existing fossil fuels. But the heat content of manure is rather low. Since, the fluidized ... -
The Uses and Morphology of Atmospheric Fluidized Bed Combustion Wastes From Canada’s First Industrial AFBC Boilers
(The American Society of Mechanical Engineers (ASME), 1987)The literature of FBC solid wastes has been critically evaluated and solid wastes from Canada’s first atmospheric fluidized bed combustion (AFBC) boilers at the Canadian Forces Base (CFB) ... -
A Review of Current Approaches to Riser Modeling
(The American Society of Mechanical Engineers (ASME), 1987)The purpose of this paper is to review the progress made during the past two decades towards the structural modeling and the numerical approaches of a more realistic riser analysis. Two or ... -
Experimental and Analytical Investigation of the Convective Diffusion of Methane Into Air
(The American Society of Mechanical Engineers (ASME), 1987)The concentration changes with time and space of methane gas were examined following its release into air at atmospheric pressure within a long smooth cylindrical tube of 2.5 in. (63.5 mm) ... -
An Improved Model for Predicting Heat Losses and Pressure Changes in Steam Injection Wells—Part 2: Model Evaluation
(The American Society of Mechanical Engineers (ASME), 1987)The improved model developed in Part 1 for predicting heat losses and pressure changes in steam injection wells is evaluated. It shows good agreement with limited field data. The improved model ... -
Nonlinear Three-Dimensional Dynamic Analysis of Marine Risers
(The American Society of Mechanical Engineers (ASME), 1987)Marine risers are modeled as thin-walled, slender, extensible or inextensible, tubular beams subject to nonlinear three-dimensional hydrodynamic loads of interactive nature, torsion and distributed ... -
Study of Friction Factor and Equivalent Diameter Correlations for Annular Flow of Non-Newtonian Drilling Fluids
(The American Society of Mechanical Engineers (ASME), 1987)Published annular pressure drop field data have been compared with values predicted by the Bingham plastic and power law models. Several different equivalent diameter equations and friction factor ...