Journal of Energy Resources Technology: Recent submissions
Now showing items 2861-2880 of 3450
-
Mediator-Assisted Electrochemical Desulfurization of Coal
(The American Society of Mechanical Engineers (ASME), 1988)A bituminous coal from Illinois (Colchester No. 2) in acid slurry was electrolyzed anodically at 1.2–1.3 V versus SCE (saturated calomel electrode) and 65–75°C. Hydrogen gas was observed ... -
A Mathematical Model for Predicting Concentration Profiles in Liquid-Solid Fine Slurry Pipe Flows
(The American Society of Mechanical Engineers (ASME), 1988)Radial solid concentration profile distributions are often present in pipe flows of fine particle slurries, and play a dominant role in controlling the behavior of the flow. This paper presents ... -
Design of the University of New Orleans Ship-Offshore University Laboratory for Offshore Industry Support
(The American Society of Mechanical Engineers (ASME), 1988)On July 23, 1987, the University of New Orleans (UNO) dedicated its new Engineering Building, which houses a 38.3 m×4.57 m×0–2.134 m deep ship-offshore university laboratory tow tank. ... -
Turbulent Jet Diffusion Flames in Environments Containing Some Premixed Fuel
(The American Society of Mechanical Engineers (ASME), 1988)The blowout limit of a methane jet diffusion flame is extended by adding small concentrations of a fuel to the surrounding air. The improvement is predicted theoretically with a model based ... -
Mass Transfer in Oil Sand Fluidized Beds—A Simplified Model
(The American Society of Mechanical Engineers (ASME), 1988)Experimental data obtained previously relating to the behavior of single spherical particles of oil sands in hot uniform velocity oxidizing gaseous streams were employed and extended to estimate ... -
Heat Transfer in the Flow of Gases Around Oil Sand Spheres
(The American Society of Mechanical Engineers (ASME), 1988)An experimental study was conducted for the combined free and forced convection heating of preshaped molded spherical particles of Athabasca oil sands in hot gaseous streams of air at low ... -
Terminal Slugcatchers for Two-Phase Flow and Dense-Phase Flow Gas Pipelines
(The American Society of Mechanical Engineers (ASME), 1988)Slugcatchers are installed at the end of two-phase pipelines and dense-phase pipelines. The technical specifications of a slugcatcher for a two-phase pipeline are based on the gas-liquid flow ... -
The Design and Engineering of Cross-Country Hydrogen Pipelines
(The American Society of Mechanical Engineers (ASME), 1988)Design of cross-country hydrogen pipelines is still uncommon. No industry-accepted codes and standards have been developed to guide the engineering and design of such facilities. A hydrogen ... -
Stress Concentration Factors in T and K-T Tubular Joints Using Finite Element Analysis
(The American Society of Mechanical Engineers (ASME), 1988)Stress concentration factors (SCFs) in a T and a K-T tubular joint have been determined using the finite element method (FEM). The SCFs are determined for basic load cases (axial load or ... -
Vortex Tube-Assisted Environmental Control of Hyperbaric Chambers
(The American Society of Mechanical Engineers (ASME), 1988)Model predictions of time histories of the temperature and humidity ratio within a hyperbaric chamber under conditions of compression and decompression are presented with and without vortex ... -
Geology of the Gladys McCall Geopressured-Geothermal Prospect, Cameron Parish, Louisiana
(The American Society of Mechanical Engineers (ASME), 1988)The Gladys McCall prospect lies at the western edge of the Rockefeller Wildlife Refuge about 88 km (55 mi) southeast of Lake Charles in Cameron Parish, Louisiana. The test well is 4825 m ... -
Seismic Response of Buried Submarine Pipelines
(The American Society of Mechanical Engineers (ASME), 1988)Submarine pipelines are many a time buried into a jet-blasted channel in the seabed. Seismic response of such buried pipelines are investigated in this paper. The earthquake is considered as ... -
Gladys McCall Geopressured Reservoir Analysis—June 1987
(The American Society of Mechanical Engineers (ASME), 1988)The Gladys McCall geopressured reservoir consists of an interbedded sequence of relatively thick sands and thin shales. The lateral extent of the reservoir is not well defined. Gladys McCall ... -
Formulas for Variation of Stress Concentration Around Intersection in Tubular Joints
(The American Society of Mechanical Engineers (ASME), 1988)Many of the offshore structures used for oil exploration and exploitation are built of tubular members. The repeated damages in tubular joints have clearly shown that the safety of these ... -
Pipeline Incidents and Emergency Repair in the North Sea
(The American Society of Mechanical Engineers (ASME), 1988)The failures of submarine pipelines in the North Sea, and the response of pipeline operators are first discussed. Against this background, the methods currently available for submarine pipeline ... -
Free Convection From a Vertical Plate With Nonuniform Surface Temperature and Embedded in a Porous Medium
(The American Society of Mechanical Engineers (ASME), 1987)A procedure is described for the calculation of heat transfer due to free convection flow along a vertical plate embedded in a porous medium with an arbitrarily varying surface temperature. ... -
An Evaluation Method for Peak/Off-Peak Price Functions in Energy Storage Technologies
(The American Society of Mechanical Engineers (ASME), 1987)A method of evaluation for peak/off-peak price functions in energy storage technologies is presented. The method is particularly useful in statical optimization of the fundamental parameters ... -
Computer Modeling of Fixed Bed Underground Coal Gasification Using the Permeation Method
(The American Society of Mechanical Engineers (ASME), 1987)A two-dimensional computational model has been developed as a pilot study for the multidimensional simulation of fixed bed underground coal gasification (UCG). The analysis is based on the finite ... -
Operational Physical Conditions for a Solid-State-Engine (SSE) Applying Shape Memory (SM) Alloy
(The American Society of Mechanical Engineers (ASME), 1987)The physical conditions for a solid-state-engine (SSE) applying shape memory (SM) alloy is treated based on both experimental results and theoretical considerations. First, the mechanical efficiency ... -
Non-Newtonian Fluid Flow in a Reservoir—An Application to Hydraulic Fracturing
(The American Society of Mechanical Engineers (ASME), 1987)A formulation for the flow of a power law non-Newtonian fluid in a porous-permeable medium represented by a nonlinear partial differential equation is presented. This governing equation is ...