Journal of Energy Resources Technology: Recent submissions
Now showing items 2601-2620 of 3450
-
Approximate Stoichiometry for Rich Hydrocarbon Mixtures
(The American Society of Mechanical Engineers (ASME), 1993) -
Experimental Investigation of Capillary-Induced Rewetting in a Flat Porous Wicking Structure
(The American Society of Mechanical Engineers (ASME), 1993)An experimental program was conducted to investigate the rewetting characteristics of liquid flowing through multiple layers of screen mesh covering a heated vertical plate. Data obtained for ... -
The Effects of Heat Transfer on Gas Spring Performance
(The American Society of Mechanical Engineers (ASME), 1993)Experiments were performed on a piston-cylinder gas spring. Speed, cyclic mean pressure, gas, bore/stroke ratio, volume ratio, and internal extended surface geometry were varied. Hysteresis loss, ... -
Friction and Wear in Threaded Surfaces of Rotary Drill Collars
(The American Society of Mechanical Engineers (ASME), 1993)Two surfaces, under high normal stress, in sliding contact provide the basis for friction and wear studies within rotary drill collars. Flat and ring specimens, considering three (3) different ... -
Scale Model Study of Pile Foundations Under Earthquake Excitation
(The American Society of Mechanical Engineers (ASME), 1993)Similitude theory is used to develop scale models for determining the earthquake response of pile foundations embedded in overconsolidated clay. The model is compared with full-scale foundations ... -
System Optimization of the Cogeneration Facility at Texas A&M University—Present Operation and Load
(The American Society of Mechanical Engineers (ASME), 1993)The combined-cycle cogeneration facility on the central campus of Texas A&M University was analyzed for its present performance and an optimized mode of operation. The analysis was carried ... -
Exergy Costing in Exergoeconomics
(The American Society of Mechanical Engineers (ASME), 1993)Existing methods of exergoeconomic analysis and optimization of energy systems operate with single average or marginal cost values per exergy unit for each material stream in the system being ... -
Finite Element Analysis of Shear Deformable Laminated Composite Plates
(The American Society of Mechanical Engineers (ASME), 1993)A shear deformable finite element is developed for the analysis of thick laminated composite plates. The finite element formulation is based on Mindlin’s plate theory in which shear correction ... -
Three-Dimensional Analysis of Extrusion Process Utilizing the Physical Modeling Technique
(The American Society of Mechanical Engineers (ASME), 1993)The purpose of this study was to simulate the metal extrusion processes via three-dimensional physical modeling technique. Plasticine was utilized as the modeling material, while plexiglass was ... -
Finding Cost-Effective Applications for Expert Systems
(The American Society of Mechanical Engineers (ASME), 1993)Expert systems are one of the few areas of artificial intelligence which have successfully made the transition from research and development to practical application. The key to fielding a ... -
A Review of Desiccant Cooling Systems
(The American Society of Mechanical Engineers (ASME), 1993)This paper describes recent published design advances that have been made in desiccant cooling systems. In desiccant cooling cycles, the desiccant reduces the humidity of the air by removing ... -
Internal Waves in a Large Offshore Storage Tank
(The American Society of Mechanical Engineers (ASME), 1993) -
Power and Refrigeration Plants for Minimum Heat Exchanger Inventory
(The American Society of Mechanical Engineers (ASME), 1993) -
A Compound Effect of Cutting Depth and Bit Dull on Cutters’ Temperature for Polycrystalline Diamond Compact Bits
(The American Society of Mechanical Engineers (ASME), 1993)This paper presents a simulation study to evaluate the combined effect of cutting depth (drilling rate) and wear (bit dull) on the thermal response of polycrystalline diamond compact (PDC) ... -
An Experimental Investigation of the Blowout Limits of a Jet Diffusion Flame in Co-Flowing Streams of Different Velocity and Composition
(The American Society of Mechanical Engineers (ASME), 1993)The blowout limits of a methane diffusion flame in a co-flowing air-fuel or air-diluent stream were determined for a range of surrounding co-flow stream velocities, both laminar and turbulent, ... -
Emf, Maximum Power and Efficiency of Fuel Cells
(The American Society of Mechanical Engineers (ASME), 1993)The ideal voltage of steady-flow fuel cells is usually expressed by Emf = −ΔG°/nF where ΔG° is the “Gibbs free energy of reaction” for the oxidation of the fuel at the supposed ... -
Ultrasonic Imaging and Velocimetry in Two-Phase Pipe Flow
(The American Society of Mechanical Engineers (ASME), 1993)This paper presents the first results of an experimental and theoretical investigation of the feasibility of using ultrasonic measurements in multiphase pipe flow. Extant downhole flow rate ... -
The Effect of the Fuel-Cell Unit Size on the Efficiency of a Fuel- Cell-Topped Rankine Power Cycle
(The American Society of Mechanical Engineers (ASME), 1993)Dunbar, Lior and Gaggioli (1991) proposed a configuration of a fuel-cell-topped electrical Rankine power generating station and analyzed its performance. That study revealed that the fuel-cell ... -
The Drilling Experience of K6-2, the High-Temperature and Crooked Geothermal Well in Kakkonda, Japan
(The American Society of Mechanical Engineers (ASME), 1993)Well K6-2 was drilled for geothermal production for the Kakkonda No. 2 Power Plant (to be built in 1995) at the Kakkonda geothermal field, northern Honshu Island, Japan from 1988 through 1989. ... -
Engineering Functional Analysis—Part I
(The American Society of Mechanical Engineers (ASME), 1993)In this paper, the essential building blocks of a new formalism called Engineering Functional Analysis (EFA) are presented. This formalism results in higher degrees of decentralization for ...