Journal of Energy Resources Technology: Recent submissions
Now showing items 2581-2600 of 3450
-
Conduction-Controlled Phase-Change Energy Storage With Radiative Heat Addition
(The American Society of Mechanical Engineers (ASME), 1994)Thermal energy storage in a phase-change material due to latent heat of fusion caused by conduction-controlled melting during radiative heat injection is considered. It is solved employing ... -
A Thermodynamic Analysis of the Lean Flammability Limits of Fuel-Diluent Mixtures in Air
(The American Society of Mechanical Engineers (ASME), 1994)A procedure is described for calculating the lean flammability limits of fuel-diluent mixtures in air over a wide range of fuel-diluent combinations and for different initial mixture temperatures. ... -
A Numerical Study of the Unsteady Effects of Droplet Evaporation and Ignition in Homogeneous Environments of Fuel and Air
(The American Society of Mechanical Engineers (ASME), 1994)The transient processes of droplet heating, vaporization and ignition in a quiescent heated environment of a homogeneous mixture of air and fuel that is potentially combustible are analyzed. A ... -
Modular Repowering of Power Plants With Nominal Ratings Lower Than 180 MW: A Rational Design Approach and Its Application to the Italian Utility System
(The American Society of Mechanical Engineers (ASME), 1994)The paper describes the rationale, the technical/economical details and the results of a study which is part of a large-scale energy conservation program enacted by the Italian Public Utility ... -
An Analytical Examination of Various Criteria for Defining Autoignition Within Heated Methane-Air Homogeneous Mixtures
(The American Society of Mechanical Engineers (ASME), 1994)Different criteria for establishing ignition within reactive methane-air mixtures are discussed. It is shown that for relatively low initial mixture temperature using the different ignition criteria ... -
Designing Surface-Mounted Components for High Reliability
(The American Society of Mechanical Engineers (ASME), 1994)Recent emphasis of the Department of Defense (DOD) on the reliability and integrity of avionics has spurred a new wave of research on this subject. This paper presents the results of a ... -
Analysis of Electric Wheeling on Cooperative Fuel Cell Cogeneration Systems Installed in Multi-Areas
(The American Society of Mechanical Engineers (ASME), 1994)The influence of electric wheeling—mutual accommodation of electric supply through an electrical grid—on both economical and energy-saving properties of cogeneration systems installed in multi-areas ... -
Tribological Performance Evaluation of Oil Mist Lubrication
(The American Society of Mechanical Engineers (ASME), 1994)In this research work, the tribological performance of oil mist lubrication (pure mist), as applied to rolling element bearings, was investigated. In the first part of this research, tests were ... -
An Experimental Investigation of Wood Combustion
(The American Society of Mechanical Engineers (ASME), 1994)This paper presents the results from an experimental investigation of wood combustion. Variables chosen for investigation are fuel moisture content, fuel particle size, excess air, fraction and ... -
The Phase Analysis of Coal Combustion Ashes
(The American Society of Mechanical Engineers (ASME), 1994)The phase composition of coal combustion ashes is important in regard to their potential uses. Here it is shown that a combination of phase separation techniques with X-ray diffraction, ... -
Gas Turbine Cycles With Solid Oxide Fuel Cells—Part I: Improved Gas Turbine Power Plant Efficiency by Use of Recycled Exhaust Gases and Fuel Cell Technology
(The American Society of Mechanical Engineers (ASME), 1994)In conventional energy conversion processes, the fuel combustion is usually highly irreversible, and is thus responsible for the low overall efficiency of the power generation process. The energy ... -
The Performance of Thermally Stable Diamonds When Used as Single Cutters Compared With Their Behavior in a Drill Bit
(The American Society of Mechanical Engineers (ASME), 1994)Experiments have been carried out to assess the rock-cutting ability of thermally stable diamond cutters of different sizes and shapes as individual cutting elements or on various drill bits. ... -
Studies on the Relative Performance of Three Oscillating Water Column Wave Energy Devices
(The American Society of Mechanical Engineers (ASME), 1994) -
Development of a General-Purpose Optimal Operational Planning System for Energy Supply Plants
(The American Society of Mechanical Engineers (ASME), 1994)A general-purpose optimal operational planning system with a user-friendly interface is developed for the purpose of determining operational strategies of energy supply plants in a simple and ... -
A Two-Temperature Model of the Regenerative Solid-Vapor Heat Pump
(The American Society of Mechanical Engineers (ASME), 1994)A thermally driven heat pump using a solid/vapor adsorption/desorption compression process is thermodynamically analyzed. Heat regeneration between the two adsorbent beds is accomplished through the ... -
Gas Turbine Cycles With Solid Oxide Fuel Cells—Part II: A Detailed Study of a Gas Turbine Cycle With an Integrated Internal Reforming Solid Oxide Fuel Cell
(The American Society of Mechanical Engineers (ASME), 1994)In conventional energy conversion processes, the fuel combustion is usually highly irreversible, and is thus responsible for the low overall efficiency of the power generation process. The energy ... -
A Laboratory-Scale Experimental Study of In-Situ Combustion Processes
(The American Society of Mechanical Engineers (ASME), 1994)A laboratory-scale experimental study of in-situ combustion for enhanced oil recovery is presented. The effects of oil saturation, preheating of the oil-sand bed, porosity of sand, and air-injection ... -
Low Invasion Corehead Reduces Mud Invasion While Improving Performances
(The American Society of Mechanical Engineers (ASME), 1994)A corehead was designed, manufactured and tested to reduce fluid invasion of the core. This is obtained by minimizing the exposure time of the core to the drilling fluid in increasing the ... -
The Wear of Thermally Stable Diamond During Rock Cutting
(The American Society of Mechanical Engineers (ASME), 1994)Single-cutter experiments have been performed to investigate the cutting and wear of thermally stable diamond (SYNDAX3) during rock cutting. Cutting forces increase linearly with depth of cut, ... -
Selection of Slim Hole Core Rods by Vibratory Analysis
(The American Society of Mechanical Engineers (ASME), 1994)This paper describes the axial, torsional, and transient buckling vibratory models developed for the selection of optimum core rod size. The axial and torsional vibratory core rod simulator ...