Journal of Energy Resources Technology: Recent submissions
Now showing items 2501-2520 of 3450
-
A Revised Decomposition Method for MILP Problems and Its Application to Operational Planning of Thermal Storage Systems
(The American Society of Mechanical Engineers (ASME), 1996)A revised decomposition method for solving large-scale mixed-integer linear programming (MILP) problems with block angular structure is presented to efficiently conduct the operational planning of ... -
Performance of a High-Solidity Wells Turbine for an OWC Wave Power Plant
(The American Society of Mechanical Engineers (ASME), 1996)The paper describes an experimental investigation, and presents the results of the aerodynamic performance of a high-solidity Wells turbine for a wave power plant. A monoplane turbine of 0.6 m ... -
Thermal Destruction Behavior of Plastic and Nonplastic Wastes in a Laboratory-Scale Facility
(The American Society of Mechanical Engineers (ASME), 1996)Experimental and theoretical studies are presented from a laboratory-scale thermal destruction facility on the destruction behavior of surrogate plastic and nonplastic solid wastes. The nonplastic ... -
A New Approach for Determining In-Situ Rock Strength While Drilling
(The American Society of Mechanical Engineers (ASME), 1996)A new method is developed for determining rock strength while drilling with a tri-cone roller bit. The technique employs the well-known “drill-off” test, using commonly measured drilling data, ... -
Operational Strategy of a Cogeneration System Under a Complex Utility Rate Structure
(The American Society of Mechanical Engineers (ASME), 1996)An operational planning problem for a cogeneration system is discussed under a complex utility rate structure which imposes demand charges due to total utility consumption over a specified period ... -
Effect of Design and Operating Parameters on the Performance of Two-Bed Sorption Heat Pump Systems
(The American Society of Mechanical Engineers (ASME), 1995)The effect of design and operating parameters on the performance of closed-cycle, two-bed sorption heat pump systems were investigated. The parameters studied in this paper included the effects ... -
Technical Editor’s Page
(The American Society of Mechanical Engineers (ASME), 1995) -
A Study of Parameters Influencing Wall-to-Bed Heat Transfer in Low-Temperature Rotary Desorbers
(The American Society of Mechanical Engineers (ASME), 1995)Heat transfer between a rotating wall and a bed of granular material is investigated. Three specific areas of this problem are studied. First, a Stefan-type model is used to evaluate the ... -
Closed-Type Solar Regenerator: Analysis and Simulation
(The American Society of Mechanical Engineers (ASME), 1995)Due to many potential problems associated with an open regeneration system in application to reconcentration with liquid desiccants, a closed-type solar regenerator has been simulated and analyzed ... -
Effect of Operating Conditions on Optimal Performance of Rotary Dehumidifiers
(The American Society of Mechanical Engineers (ASME), 1995)The design-point dehumidification performance (i.e., at ARI conditions) of a rotary dehumidifier wheel depends on its rotational speed, the sorption properties of the desiccant, the heat and mass ... -
A Mathematical Model of a Tubular Solid Oxide Fuel Cell
(The American Society of Mechanical Engineers (ASME), 1995)The solid oxide fuel cell shows great potential as an efficient energy conversion system for use in central power stations. These cells can reform most hydrocarbon fuels with air to produce ... -
Detonation Cell Widths in Hydrogen/Oxygen/Diluent Mixtures at Low Initial Pressures
(The American Society of Mechanical Engineers (ASME), 1995)Detonation cell widths of hydrogen/oxygen/helium/steam mixtures were determined in 15 and 30-cm internal-diameter pipes using the smoked-foil technique. The investigations were carried out over a ... -
Modeling of Twofold Flame Behavior of Ceramic Foam Surface Burners
(The American Society of Mechanical Engineers (ASME), 1995)A model for the flame behavior of a ceramic foam surface gas burner is developed. The burner plate is divided into small segments. Each segment is assumed to behave independently and the ... -
A Unified Model for Slug Flow in Upward Inclined Pipes
(The American Society of Mechanical Engineers (ASME), 1995)The effect of pipe inclination on upward two-phase slug flow characteristics has been studied both experimentally and theoretically. Experimental data were acquired for the entire range of ... -
An Experimental Study of the Interaction of Multiple Liquid Pool Fires
(The American Society of Mechanical Engineers (ASME), 1995)The risk of accidental spills and possible fires is high in the storage and handling of large quantities of flammable liquids. Such liquid pool fires are generally buoyancy-driven and emit a ... -
Explicit Solutions for the Antiplane Problem of Bonded Dissimilar Materials with Two Concentric Circular-Arc Inclusions
(The American Society of Mechanical Engineers (ASME), 1995)A general solution to the antiplane problem of two concentric circular-arc inclusions in bonded dissimilar materials is provided. Based upon the Hilbert problem formulation and the technique of ... -
Characterization of Solid Wastes From Circulating Fluidized Bed Combustion
(The American Society of Mechanical Engineers (ASME), 1995)The characterization of solid wastes from full-scale circulating fluidized bed combustors (CFBC) is necessary to ensure that disposal procedures or utilization strategies for the waste solids are ... -
Preliminary Investigation of Cycle-to-Cycle Variations in a Nonair-Breathing Diesel Engine
(The American Society of Mechanical Engineers (ASME), 1995)The effect of nonair mixtures on cycle-to-cycle variations of cylinder pressure characteristics was investigated experimentally with an indirect-injected (IDI) diesel engine. The engine intake ... -
Waste-Heat Recovery in Batch Processs Using Heat Storage
(The American Society of Mechanical Engineers (ASME), 1995)The waste-heat recovery in batch processes has been studied using the pinch-point method. The aim of the work has been to investigate theoretical and practical approaches to the design of ... -
Reliability-Based Casing Design
(The American Society of Mechanical Engineers (ASME), 1995)The present paper describes the development of reliability-based design criteria for oil and/or gas well casing/tubing. The approach is based on the fundamental principles of limit state design. ...