Journal of Energy Resources Technology: Recent submissions
Now showing items 2401-2420 of 3450
-
Entropy Generation in Multicomponent Reacting Flows
(The American Society of Mechanical Engineers (ASME), 1998)A comprehensive equation to determine the rate of local entropy generation in multicomponent, reacting, laminar fluid flow involving heat and mass transfer is formulated based on species-average ... -
Geochemical Partitioning of Metals in Spent Drilling Fluid Solids
(The American Society of Mechanical Engineers (ASME), 1998)Metals in oil and gas fluids have been of concern to the environmental and industrial communities since 1976. As a result, metals in 31 spent drilling fluids representative of the major oil ... -
Mechanisms of Bed Material Agglomeration in a Petroleum Coke-Fired Circulating Fluidized Bed Boiler
(The American Society of Mechanical Engineers (ASME), 1998)Petroleum coke firing in a circulating fluidized bed boiler has sometimes been reported to be associated with cyclone deposit problems and return leg plugging. In this paper, we present data ... -
Using Genetic Algorithms and the Exergonomic Approach to Optimize District Heating Networks
(The American Society of Mechanical Engineers (ASME), 1998)This paper discusses the application of exergy analysis to a district heating network (DHN) currently in operation in Brescia (Italy). The purpose is to compare the existing system design with ... -
The Study of Dynamic Slug Flow Characteristics Using Digital Image Analysis—Part I: Flow Visualization
(The American Society of Mechanical Engineers (ASME), 1998)This paper reports the application of novel, digital image analysis techniques in the study of slug flow characteristics, under dynamic conditions in two-phase gas-liquid mixtures. Water and an ... -
Thermodynamic Optimization of a Gas Turbine Power Plant With Pressure Drop Irreversibilities
(The American Society of Mechanical Engineers (ASME), 1998)In this paper we show that the thermodynamic performance of a gas turbine power plant can be optimized by adjusting the flow rate and the distribution of pressure losses along the flow path. ... -
Agglomeration and Fouling in Petroleum Coke-Fired FBC Boilers
(The American Society of Mechanical Engineers (ASME), 1998)Experiments have been done subjecting ashes from industrial-scale FBC boilers to sulphating conditions in an oven for up to 105 days. These show that sulphation by itself causes agglomeration ... -
Numerical Simulations of Highly Preheated Air Combustion in an Industrial Furnace
(The American Society of Mechanical Engineers (ASME), 1998)The numerical simulations of reactive turbulent flows and heat transfer in an industrial slab reheat furnace in which the combustion air is highly preheated have been carried out. The influence ... -
Overall Efficiency of a Radial Fin Assembly Under Dehumidifying Conditions
(The American Society of Mechanical Engineers (ASME), 1998)The aim of this paper is the analysis of heat transfer in a radial fin assembly during the process of dehumidification. An individual finned tube geometry is a reasonable representation of ... -
Transport to a Chemically Active Thin Liquid Film Over a Spinning Disk
(The American Society of Mechanical Engineers (ASME), 1998)An analytical solution for the process of mass transfer from a spinning disk to a chemically active thin liquid film flowing over the disk is presented. By analogy, the results are also ... -
Analysis of Yield-Power-Law Fluid Flow in Irregular Eccentric Annuli
(The American Society of Mechanical Engineers (ASME), 1998)Fully developed laminar axial flow of yield-power-law fluids in eccentric annuli has been investigated numerically. The annuli may be fully open or partially blocked. General nonorthogonal, ... -
Type Curves for Predicting Directional Tendencies of Simple Bottom-Hole Assemblies
(The American Society of Mechanical Engineers (ASME), 1998)The paper provides solutions for predicting directional tendencies of slick and single stabilizer bottom-hole assemblies (BHA) in curved boreholes. Solutions are derived in a curvilinear system ... -
Performance Characteristics of a Compressor-Driven Metal Hydride Refrigerator
(The American Society of Mechanical Engineers (ASME), 1998)Thermodynamic analyses of compressor-driven metal hydride refrigerators predict a high coefficient of performance. Comparison with the results from a computational model indicates that the coefficient ... -
Liquid Holdup in Large-Diameter Horizontal Multiphase Pipelines
(The American Society of Mechanical Engineers (ASME), 1998)This paper studies the liquid holdup within the mixing zone of the slug. The results of the study show that the liquid holdup begins at the liquid holdup of the liquid film before the slug ... -
Discussion: “Liquid Holdup in Large-Diameter Horizontal Multiphase Pipelines” (Maley, L. C. and Jepson, W. P. 1998, ASME J. Energy Resour. Technol., 120, pp. 185–191)
(The American Society of Mechanical Engineers (ASME), 1998) -
Pipe Bending and Running Forces in Medium to High-Curvature Wells Using Finite Element Analysis
(The American Society of Mechanical Engineers (ASME), 1998)The present paper describes the running process in horizontal wells and studies the effect of some factors on running forces required to push pipes through curved holes with short to medium ... -
Evaluation of Several Turbulence Models for Turbulent Flow in Concentric and Eccentric Annuli
(The American Society of Mechanical Engineers (ASME), 1998)Turbulent flow in concentric and eccentric annuli is numerically simulated as part of an investigation aimed at modeling drilled cuttings transport in wellbores. A numerical code is developed ... -
Oilwell Cement Pulsing to Maintain Hydrostatic Pressure—A Search for Design Model
(The American Society of Mechanical Engineers (ASME), 1998)Presented are theoretical and experimental results from a project supporting development of a new method for cement vibration in well’s annulus to prevent gas migration. In this method, cyclic ... -
On the Use of Wind-Wave Spectral Formulas to Estimate Wave Energy
(The American Society of Mechanical Engineers (ASME), 1998)It is common practice by wave energy conversion technologists to estimate long-term wave energy potentials at both offshore and coastal sites by using established wind-wave spectral formulas. It ... -
Analysis of Offshore Guyed Tower Platforms to Wind and Wave Forces
(The American Society of Mechanical Engineers (ASME), 1998)The fundamental frequency of guyed tower platforms is designed to be low, and, therefore, it is susceptible to low-frequency excitation caused by fluctuating components of the wind velocity. The ...