Journal of Energy Resources Technology: Recent submissions
Now showing items 2381-2400 of 3450
-
The Effect of Drillpipe Rotation on Annular Frictional Pressure Loss
(The American Society of Mechanical Engineers (ASME), 1998)Accurate predictions of annular frictional pressure losses (AFPL) are important for optimal hydraulic program design of both vertical and horizontal wells. In this study, the effects of drillpipe ... -
Incorporating a District Heating/Cooling System Into an Existing Geothermal Power Plant
(The American Society of Mechanical Engineers (ASME), 1998)Geothermal energy has been used for power generation, space and process heating, and to a lesser extent, space cooling. However, it is rarely used for cogeneration. This paper shows how a ... -
Predicting Single-Phase and Two-Phase Non-Newtonian Flow Behavior in Pipes
(The American Society of Mechanical Engineers (ASME), 1998)Improved and novel prediction methods are described for single-phase and two-phase flow of non-Newtonian fluids in pipes. Good predictions are achieved for pressure drop, liquid holdup fraction, ... -
Prediction and Validation of Blowout Limits of Co-Flowing Jet Diffusion Flames—Effect of Dilution
(The American Society of Mechanical Engineers (ASME), 1998)The blowout limits of a co-flowing turbulent methane jet diffusion flame with addition of diluent in either jet fuel or surrounding air stream is studied both analytically and experimentally. ... -
Effects of Flame Lift-Off on the Differences Between the Diffusion Flames From Circular and Elliptic Burners
(The American Society of Mechanical Engineers (ASME), 1998)An experimental study conducted to determine the effects of lifting the flame base off the burner rim on the differences between the flame characteristics of diffusion flames from circular and ... -
The Relationship of Optimum Heat Exchanger Allocation and Minimum Entropy Generation Rate for Refrigeration Cycles
(The American Society of Mechanical Engineers (ASME), 1998)This paper investigates the effect of heat exchanger allocation on overall system performance using both reverse Carnot and vapor compression refrigeration cycle models to calculate system performance ... -
Investigation of Holdup and Pressure Drop Behavior for Oil-Water Flow in Vertical and Deviated Wells
(The American Society of Mechanical Engineers (ASME), 1998)Two-phase flow of oil and water is commonly observed in wellbores, and its behavior under a wide range of flow conditions and inclination angles constitutes a relevant unresolved issue for the ... -
Effect of Drag-Reducing Agents in Multiphase Flow Pipelines
(The American Society of Mechanical Engineers (ASME), 1998)The effect of drag-reducing agents (DRA) on pressure gradient and flow regime has been studied in horizontal and 2-deg upward inclined pipes. Experiments were conducted for different flow regimes ... -
Numerical Simulation of Hydrate Transport in Natural Gas Pipeline
(The American Society of Mechanical Engineers (ASME), 1998)Accurate modeling of hydrate transportation in natural gas pipelines is becoming increasingly important in the design and operation of offshore production facilities. The dynamics involved in the ... -
A Desiccant Dehumidifier for Electric Vehicle Heating
(The American Society of Mechanical Engineers (ASME), 1998)Vehicle heating requires a substantial amount of energy. Electric vehicles (EVs) generate little waste heat, and using battery energy for heating may consume a substantial fraction of the energy ... -
Dynamic Differential Pressure Effects on Drilling of Permeable Formations
(The American Society of Mechanical Engineers (ASME), 1998)In the mathematical modeling of bit penetration rate for tri-cone roller bits in permeable formations, virtually all of the current techniques assume that the differential pressure between the ... -
Borehole Failure Resulting From Formation Integrity (Leak-Off) Testing in Upper Marine Sediments Offshore
(The American Society of Mechanical Engineers (ASME), 1998)This paper presents the results of a theoretical study, supported with the finite element analysis, into potential loss of external integrity around a casing shoe resulting from leak-off testing ... -
Retractable Bits Development and Application
(The American Society of Mechanical Engineers (ASME), 1998)This paper presents a historical view and present status of retractable bit design and drilling results. Despite the significant improvements in cone-sealed bearing rock bits, the special features ... -
Dispersion—An Entropy Generator of Diffusion
(The American Society of Mechanical Engineers (ASME), 1998)In multicomponent gaseous flows with chemical reactions, diffusion is usually considered to be a single-source entropy generator. Introducing the concept of dispersion, where the atom balance is ... -
Thermodynamic Definition and Quantum-Theoretic Pictorial Illustration of Entropy
(The American Society of Mechanical Engineers (ASME), 1998)Cannot analyzed an engine operating between two reservoirs. Through a peculiar mode of reasoning, he found the correct optimum shaft work done during a cyclic change of state of the engine. ... -
Thermodynamics of Insulated Pressure Vessels for Vehicular Hydrogen Storage
(The American Society of Mechanical Engineers (ASME), 1998)This paper studies the application of insulated pressure vessels for hydrogen-fueled light-duty vehicles. Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with ... -
Efficiency Optimizations of an Irreversible Brayton Heat Engine
(The American Society of Mechanical Engineers (ASME), 1998)A steady-flow approach for finite-time thermodynamics is used to calculate the maximum thermal efficiency, its corresponding power output, adiabatic temperature ratio, and thermal-conductance ratio ... -
The Study of Dynamic Slug Flow Characteristics Using Digital Image Analysis—Part II: Modeling Results
(The American Society of Mechanical Engineers (ASME), 1998)A definition is given for a Froude number in the liquid film ahead of the slug and it is seen that slug characteristics are strongly influenced by the Froude number. The mechanisms in the ... -
Sizing Wet-Gas Pipelines and Slug Catchers With Steady-State Multiphase Flow Simulations
(The American Society of Mechanical Engineers (ASME), 1998)The design of wet-gas pipelines and slug catchers requires multiphase flow simulations, both steady-state and transient. However, steady-state simulation is often inadequately conducted and its ... -
Application of the First and Second Laws to Fuel Minimization in a Batch Furnace
(The American Society of Mechanical Engineers (ASME), 1998)This paper presents results for the minimization of fuel consumption in a batch furnace. Several different criteria are used and minimized with respect to time-dependent process and control ...