Journal of Energy Resources Technology: Recent submissions
Now showing items 2361-2380 of 3450
-
Drag Reduction in Heavy Oil
(The American Society of Mechanical Engineers (ASME), 1999)Transporting heavy crude oil by pipeline requires special facilities because the viscosity is so high at normal field temperatures. In some cases the oil is heated with special heaters along ... -
Investigation of Drilling Fluids Containing Blast Furnace Slag for Their Potential Impact on Formation Damage—A Laboratory Study
(The American Society of Mechanical Engineers (ASME), 1999)This work discusses the effect of incorporating blast furnace slag (BFS) as an additive in water-based drilling fluids. The intent of this treatment is rapid development of a thin, impervious, ... -
Flow Testing Methods to Detect and Characterize Partial Blockages in Looped Subsea Flowlines
(The American Society of Mechanical Engineers (ASME), 1999)Looping subsea flowlines is one method being utilized for flow assurance. Looping allows the possibility of circulating chemicals and/or tools to remediate partial flowline blockages due to wax, ... -
A Two-Dimensional Numerical Study of Heat Transfer in a Finned Tube Assembly During Axisymmetric Dehumidification
(The American Society of Mechanical Engineers (ASME), 1999)This paper presents the analysis of two-dimensional heat transfer in an annular finned tube assembly during the process of dehumidification. All possible fin surface conditions, namely, dry, fully ... -
The Impact of the Model of the Environment in Exergy Analyses
(The American Society of Mechanical Engineers (ASME), 1999)The values of absolute exergy and exergetic efficiency depend on the assumed values of the “reference states,” which are essentially a model of the environment of the processes and components ... -
Retrofitting a Geothermal Power Plant to Optimize Performance: A Case Study
(The American Society of Mechanical Engineers (ASME), 1999)Performance evaluation of a 12.8-MW single-flash design geothermal power plant in Northern Nevada is conducted using actual plant operating data, and potential improvement sites are identified. ... -
Thermoeconomic Optimization of a Sensible-Heat Thermal-Energy-Storage System: A Complete Storage Cycle
(The American Society of Mechanical Engineers (ASME), 1999)An analytical model for the second-law-based thermoeconomic analysis and optimization of a sensible-heat-storage system is derived and discussed, in which the storage element is both heated and ... -
ETCE/OMAE 2000
(The American Society of Mechanical Engineers (ASME), 1999) -
Velocity Guidelines for Avoiding Erosion-Corrosion Damage in Sweet Production With Sand
(The American Society of Mechanical Engineers (ASME), 1998)CO2 corrosion in carbon steel piping systems can be severe depending on a number of factors including CO2 content, water chemistry, temperature, and percent water cut. For many oil and gas ... -
Editorial
(The American Society of Mechanical Engineers (ASME), 1998) -
Editorial
(The American Society of Mechanical Engineers (ASME), 1998) -
An Analysis of the Design Loads Placed on a Well by a Diverter System
(The American Society of Mechanical Engineers (ASME), 1998)Diverter systems, used as a means of well control while drilling surface hole, have a history of occasional failure. This paper addresses excessive back pressure, which can result in mechanical ... -
Drill String Safety Valve Reliability: Experimental Measurements of Actuating Torque
(The American Society of Mechanical Engineers (ASME), 1998)Drill string safety valves (DSSVs) are used to prevent blowouts up the drillpipe when unexpected subsurface pressures are encountered in oil and gas drilling. Several case history reviews of ... -
Evaluation of the Backpressure Technique for Blockage Detection in Gas Flowlines
(The American Society of Mechanical Engineers (ASME), 1998)As longer, full well-stream flowlines are utilized to reduce the costs of deepwater and satellite developments, routine production monitoring attains a new level of importance. Of particular ... -
A New Look at Measurement Uncertainty of Multiphase Flow Meters
(The American Society of Mechanical Engineers (ASME), 1998)At present, no standard of presenting multiphase flow meter (MPFM) uncertainties has been accepted by industry. Consequently, vendors’ specifications may only indicate velocity and component fraction ... -
Numerical Simulation of the Gas-Liquid Flow in a Rotary Gas Separator
(The American Society of Mechanical Engineers (ASME), 1998)The presence of free gas at the pump intake adversely affects the performance of an electrical submersible pump (ESP) system, often resulting in low efficiency and causing operational problems. ... -
Design and Performance of Passive Control System for Gas-Liquid Cylindrical Cyclone Separators
(The American Society of Mechanical Engineers (ASME), 1998)The performance of gas-liquid cylindrical cyclone (GLCC) separators can be improved by reducing or eliminating liquid carryover into the gas stream or gas carryunder through the liquid stream, ... -
Transients in Gas-Condensate Natural Gas Pipelines
(The American Society of Mechanical Engineers (ASME), 1998)Liquid condensation in natural gas transmission pipelines commonly occurs due to the thermodynamic and hydrodynamic imperatives. Condensation subjects the gas pipeline to two-phase transport. Neither ... -
Disturbed Flow and Flow-Accelerated Corrosion in Oil and Gas Production
(The American Society of Mechanical Engineers (ASME), 1998)The effect of fluid flow on corrosion of steel in oil and gas environments involves a complex interaction of physical and chemical parameters. The basic requirement for any corrosion to occur ... -
Multiphase Flow-Enhanced Corrosion Mechanisms in Horizontal Pipelines
(The American Society of Mechanical Engineers (ASME), 1998)Previous work has demonstrated the mechanism of enhanced corrosion in slug flow due to entrained pulses of gas bubbles (Gopal et al., 1997). Corrosion rate measurements have been made at ...