Journal of Energy Resources Technology: Recent submissions
Now showing items 2341-2360 of 3450
-
Effect of Air Preheat Temperature and Oxygen Concentration on Flame Structure and Emission
(The American Society of Mechanical Engineers (ASME), 1999)The structure of turbulent diffusion flames with highly preheated combustion air (air preheat temperature in excess of 1150°C) has been obtained using a specially designed regenerative ... -
Three-Dimensional Laser Heating Model and Entropy Generation Consideration
(The American Society of Mechanical Engineers (ASME), 1999)Lasers find wide applications in heat treatment of engineering parts. The modeling and energy analysis of the heating process can reduce substantially the time required for process optimization ... -
Effect of Drag-Reducing Agent on Slug Characteristics in Multiphase Flow in Inclined Pipes
(The American Society of Mechanical Engineers (ASME), 1999)The effect of drag-reducing agent (DRA) on multiphase flow in upward and downward inclined pipes has been studied. The effect of DRA on pressure drop and slug characteristics such as slug ... -
Modeling of Multiphase Wax Deposition
(The American Society of Mechanical Engineers (ASME), 1999)The environmental conditions typically encountered in deepwater petroleum operations lead to a number of production problems. The cold environment promotes particle formation and deposition of ... -
Estimation of Two-Phase Flow Heat Transfer in Pipes
(The American Society of Mechanical Engineers (ASME), 1999)Heat transfer can be of importance in the design of multiphase petroleum flowlines. However, heat transfer data for gas-liquid flows are available only for small-diameter pipes at low pressures. ... -
The Impact of Adding Nitrogen Substitutes to Conventional Automotive Fuels
(The American Society of Mechanical Engineers (ASME), 1999)The adoption of oxygenates in gasoline was originally spurred by the oil crises of the 1970s. In more recent years, public awareness of the environmental issues constituted the main reason for ... -
ASME International Petroleum Division—75th Anniversary
(The American Society of Mechanical Engineers (ASME), 1999) -
Theoretical Study of Mode Localization Phenomenon in Bottom-Hole Assemblies in Oil-Well Drilling
(The American Society of Mechanical Engineers (ASME), 1999)The mode localization phenomena in bottom-hole assemblies (BHA) used in oil-well drilling is investigated. A fully gaged stabilizer model is shown to produce weak coupling between segments of ... -
Modeling of a Heat Pump With Evaporator Air Dehumidification for Reduced Frost Formation
(The American Society of Mechanical Engineers (ASME), 1999)This paper presents an analysis of a heat pump that uses a solid desiccant dehumidifier to reduce the humidity of the ambient air that flows into the evaporator, with the purpose of decreasing ... -
Improving the Performance of an Existing Air-Cooled Binary Geothermal Power Plant: A Case Study
(The American Society of Mechanical Engineers (ASME), 1999)An existing air-cooled binary geothermal power plant in northern Nevada is studied. The current performance of the plant is analyzed with an emphasis on the effects of seasonal climate changes. ... -
Commercial Boiler Waste-Heat Utilization for Air Conditioning in Developing Countries
(The American Society of Mechanical Engineers (ASME), 1999)This study investigates the utilization of waste heat from commercial process steam boilers for air conditioning using absorption cooling systems. An ammonia-water generator absorber heat exchange ... -
A New Method of Steam Quality Measurement Based on Ultrasound
(The American Society of Mechanical Engineers (ASME), 1999)A new method of measuring the steam quality based on ultrasound is presented in this paper. This method is based on rigorous consideration of the steam’s thermodynamic properties. It is shown ... -
Effect of Coiled Tubing Initial Configuration on Buckling Behavior in Deviated Wells
(The American Society of Mechanical Engineers (ASME), 1999)Current sinusoidal and helical buckling models are valid only for initially straight coiled tubing (CT). This paper stresses the effect of the pipe initial configuration (residual bending) on ... -
Leak Detection in Liquid Subsea Flowlines With no Recorded Feed Rate
(The American Society of Mechanical Engineers (ASME), 1999)This paper presents a statistical method to detect leaks in subsea liquid flowlines when the inlet flow rate measurements are unavailable and conventional mass balance techniques cannot be used. ... -
Resistive Force of Wax Deposits During Pigging Operations
(The American Society of Mechanical Engineers (ASME), 1999)One of the forces that act on a pig while in operation in a pipeline is that due to the layer of wax deposited on the pipeline wall. Therefore, if the motion of a pig or its cleaning ... -
Optimal Planning of a Cascade-Type Multistage Refrigeration System for a Beverage Plant
(The American Society of Mechanical Engineers (ASME), 1999)An optimal planning method is presented for a cascade-type multistage refrigeration system. Heat exchange areas of evaporator, condenser, and beverage cooler are determined optimally so as to ... -
Plunger Lift Versus Velocity Strings
(The American Society of Mechanical Engineers (ASME), 1999)Plunger lift and velocity strings are two common methods of attacking liquid loading problems in gas wells. This paper shows how to compare the calculated performance of both methods at downhole ... -
Minimum Irreversibility Criteria for Heat Exchanger Configurations
(The American Society of Mechanical Engineers (ASME), 1999)From the second law of thermodynamics, the concepts of irreversibility, entropy generation, and availability are applied to counterflow, parallel-flow, and cross-flow heat exchangers. In the case ... -
Optimal Operation of a Gogeneration Plant in Consideration of Equipment Startup/Shutdown Cost
(The American Society of Mechanical Engineers (ASME), 1999)A rational method of determining the operational strategy of energy supply plants in consideration of equipment startup/shutdown cost is proposed. The operational planning problem is formulated ... -
Improvements of a Molten Carbonate Fuel Cell Power Plant via Exergy Analysis
(The American Society of Mechanical Engineers (ASME), 1999)A proposed molten carbonate fuel cell power plant design, intended for commercial production by the end of the 1990s and developed under the auspices of the U.S. Department of Energy, the Gas ...