Journal of Energy Resources Technology: Recent submissions
Now showing items 2321-2340 of 3450
-
Thermodynamic Performance of Ice Thermal Energy Storage Systems
(The American Society of Mechanical Engineers (ASME), 2000)The thermodynamic performance of an encapsulated ice thermal energy storage (ITES) system for cooling capacity is assessed using exergy and energy analyses. A full cycle, with charging, storing, ... -
One-Dimensional Simulations of Jet Fuel Thermal-Oxidative Degradation and Deposit Formation Within Cylindrical Passages
(The American Society of Mechanical Engineers (ASME), 2000)Flowing aviation fuel is used as a coolant in military aircraft. Dissolved O2 reacts with the heated fuel to form undesirable surface deposits which disrupt the normal flow. For purposes of ... -
Application of Flamelet Profiles to Flame Structure in Practical Burners
(The American Society of Mechanical Engineers (ASME), 1999)Partial premixing can be induced by design in combustors, occurs inadvertently during turbulent nonpremixed combustion, or arises through inadequate fuel-air mixing. Therefore, it is of interest ... -
Effects of Evaporator Frosting on the Performance of an Air-to-Air Heat Pump
(The American Society of Mechanical Engineers (ASME), 1999)This paper shows the development and use of a transient model for evaluating frost formation on a parallel-plate heat pump evaporator. A frost formation model is derived by applying the equations ... -
Flow Field Prediction and Bubble Trajectory Model in Gas-Liquid Cylindrical Cyclone (GLCC) Separators
(The American Society of Mechanical Engineers (ASME), 1999)Several mechanistic models have been already developed for predicting the onset of liquid carryover in gas-liquid cylindrical cyclone (GLCC) separators. However, currently no model is available ... -
Aspect Ratio Modeling and Design Procedure for GLCC Compact Separators
(The American Society of Mechanical Engineers (ASME), 1999)The petroleum industry has recently shown interest in the development of innovative alternatives to the conventional vessel-type separator. One such alternative is the gas-liquid cylindrical cyclone ... -
Effects of Adsorbent Conductivity and Permeability on the Performance of a Solid Sorption Heat Pump
(The American Society of Mechanical Engineers (ASME), 1999)Solid sorption heat pumps can improve the effectiveness with which energy resources are used for heating and cooling. These systems operate by alternately heating and cooling beds of adsorbent ... -
Estimation of the Thermodynamic Properties of Unbranched Hydrocarbons
(The American Society of Mechanical Engineers (ASME), 1999)A simple model has been developed to estimate the sensible thermodynamic properties such as Gibbs free energy, enthalpy, heat capacity, and entropy of unbranched hydrocarbons over a wide range ... -
Time-Dependent Failure Analysis of Inclined Boreholes in Fluid-Saturated Formations
(The American Society of Mechanical Engineers (ASME), 1999)This paper presents time-dependent poroelastic failure analyses of boreholes drilled in directions inclined to the far-field stress principal axes in fluid-saturated isotropic porous formations. The ... -
Analytical Inflow Performance Relationships
(The American Society of Mechanical Engineers (ASME), 1999)The performance of oil wells producing during boundary-dominated flow was investigated to develop a better understanding of multiphase flow and its effects on single well performance. This ... -
Chemical Plug for Zone Isolation in Horizontal Wells
(The American Society of Mechanical Engineers (ASME), 1999)A laboratory study has been conducted on the use of chemical plugs, instead of conventional mechanical packers, to isolate water and gas-producing zones in horizontal wells. Results of experiments ... -
A Mechanistic Model for Predicting Pressure Drop in Vertical Upward Two-Phase Flow
(The American Society of Mechanical Engineers (ASME), 1999)A comprehensive mechanistic model is formulated to predict flow patterns, pressure drop, and liquid holdup in vertical upward two-phase flow. The model identifies five flow patterns: bubble, ... -
Sensitivity Analysis of Absorption Cycle Fluid Thermodynamic Properties
(The American Society of Mechanical Engineers (ASME), 1999)Absorption heat pump technology may be improved by new cycle configurations by new working fluids. In this study, the effect of hypothetical working fluids on performance improvement is explored. ... -
New Model to Analyze Nonlinear Leak-Off Test Behavior
(The American Society of Mechanical Engineers (ASME), 1999)A leak-off test (LOT) is a verification method to estimate fracture pressure of exposed formations. After cementing each casing string, LOT is run to verify that the casing, cement and formation ... -
Stator Life of a Positive Displacement Downhole Drilling Motor
(The American Society of Mechanical Engineers (ASME), 1999)The power section of a positive displacement drill motor (PDM) consists of a steel rotor and a tube with a molded elastomeric lining (stator). Power section failures are typically due to the ... -
Investigation of Flow Regime Transitions in Large-Diameter Inclined Pipes
(The American Society of Mechanical Engineers (ASME), 1999)Multiphase oil/water/gas flow regime transition studies are carried out in a 10-cm i.d., 18-m long pipe at inclinations of ±2 deg at system pressures between 0 to 0.79 MPa. The results ... -
Co-Current and Countercurrent Migration of Gas Kicks in “Horizontal” Wells
(The American Society of Mechanical Engineers (ASME), 1999)Results from experiments conducted in downward liquid-gas flows in inclined, eccentric annular pipes, with water and air as the working fluids, are presented. The gas was injected in the middle ... -
Efficiency Comparisons for a Centrifugal Separator Using Hydrocarbon Fluids and Steam and Water
(The American Society of Mechanical Engineers (ASME), 1999)During 1996 and 1997, a steam and water separator used in the nuclear power industry was tested with hydrocarbon fluids to evaluate its potential for use in the hydrocarbon production industry. ... -
The Relative Importance of Radicals on the N2O and NO Formation and Destruction Paths in a Quartz CFBC
(The American Society of Mechanical Engineers (ASME), 1999)In a laboratory-scale circulating fluidized bed combustor (CFBC), which mainly consists of quartz-glass, the relative importance of the radicals, generated by the combustion process, on the N2 O ... -
On Total Variation Diminishing Schemes for Pressure Transients
(The American Society of Mechanical Engineers (ASME), 1999)A higher-order numerical procedure is applied to simulate typical transient phenomena in natural gas transportation. Reliable modeling and prediction of transients features in transmission pipelines ...