Journal of Energy Resources Technology: Recent submissions
Now showing items 2421-2440 of 3450
-
Effect of Torsion on Stability, Dynamic Forces, and Vibration Characteristics in Drillstrings
(The American Society of Mechanical Engineers (ASME), 1997)Traditionally, the analysis of stability in drillstrings is based on longitudinal vibrations only. However, field experience indicates the presence of torsional effects in the form of modulations ... -
An Analytical Approach to Understanding the “Pressure Gain” Combustor
(The American Society of Mechanical Engineers (ASME), 1997)Although pulse combustion has been successfully utilized in various commercial applications, one potential application yet to reach the market is the pressure gain gas turbine (PGGT). A PGGT ... -
Lift-Off Stability of n-Heptane Jet Diffusion Flames in Homogeneous Environments of Fuel and Air
(The American Society of Mechanical Engineers (ASME), 1997)The lift-off of jet diffusion flames of a liquid fuel in coflowing streams of air was established experimentally for a range of jet discharge and stream velocities. The improvement in the ... -
A Review of Multiphase Flow Through Chokes
(The American Society of Mechanical Engineers (ASME), 1997)Three comprehensive mechanistic models (Ashford and Pierce, 1974; Sachdeva et al., 1986; Perkins, 1990) dealing with multiphase flow through chokes have been studied. Their common purpose is to ... -
A New Mechanism for FBC Agglomeration and Fouling in 100 Percent Firing of Petroleum Coke
(The American Society of Mechanical Engineers (ASME), 1997)In an effort to clarify the causes of agglomeration and fouling in fluidized bed combustion of petroleum coke, a detailed study was made of samples taken from different locations of an ... -
Near-Boom Oil-Slick Instability Criterion in Viscous Flows and the Influence of Free-Surface Boundary Conditions
(The American Society of Mechanical Engineers (ASME), 1997)Booms are often used to contain oil spills prior to various oil removal techniques. Under certain conditions, the oil droplets can leave the oil slick and enter the water. A simple balance ... -
Mixed Convection in Non-Newtonian Fluids Along a Horizontal Plate in a Porous Medium
(The American Society of Mechanical Engineers (ASME), 1997)The problem of mixed convection from horizontal surfaces in a porous medium saturated with a power-law-type non-Newtonian fluid is investigated. The transformed conservation laws are solved ... -
Thermal Stress Analysis of a Subsurface Inclined Crack Subjected to a Point Heat Source
(The American Society of Mechanical Engineers (ASME), 1997)The thermoelastic response of a subsurface inclined crack under the application of a point heat source is studied in this paper. Based on the complex variable theory and the method of analytical ... -
An Experimental and Analytical Study of Single-Phase Liquid Flow in a Horizontal Well
(The American Society of Mechanical Engineers (ASME), 1997)A new test facility was designed and constructed to simulate flow in a horizontal well with a single perforation. A total of 635 tests were conducted with Reynolds numbers ranging from 5000 ... -
Exergonomic Optimization of an Air-Conditioning System
(The American Society of Mechanical Engineers (ASME), 1997)In this paper, exergonomic theory is applied to an air-conditioning system for optimization purposes. The investigation is addressed to an all-air system with air recirculation, The thermodynamic ... -
Addition of Highly Efficient Bottoming Cycles for the Nth-Generation Molten Carbonate Fuel Cell Power Plant
(The American Society of Mechanical Engineers (ASME), 1997)An intermediate scale (2.0 MW gross) molten carbonate fuel cell (MCFC) power plant recently began operating in Santa Clara, California. The goal of the project is to demonstrate the possibility ... -
Effect of Air Distribution on Solid Fuel Bed Combustion
(The American Society of Mechanical Engineers (ASME), 1997)One important aspect of refuse mass-burn combustion control is the manipulation of combustion air. Proper air manipulation is key to the achievement of good combustion efficiency and reduction ... -
A Numerical Study of Droplet Evaporation and Combustion in the Presence of an Oscillating Flow
(The American Society of Mechanical Engineers (ASME), 1997)The two-dimensional, unsteady, laminar conservation equations for mass, momentum, energy, and species transport in the gas phase are solved numerically in spherical coordinates in order to study ... -
Relating Burning Rate and NO Formation to Pressure Development in Two-Stroke Diesel Engines
(The American Society of Mechanical Engineers (ASME), 1997)A multizone thermodynamic method has been developed to determine combustion rate and NO formation from measured cylinder pressures and performance of two-stroke diesel engines. Integral to the ... -
The Deformation of O-Rings Compressed by Smooth Rigid Plates
(The American Society of Mechanical Engineers (ASME), 1997)Three-dimensional effects of symmetrically compressing an O-ring with rigid plates are investigated. The O-ring is assumed to be an incompressible elastic material and the mixed boundary value ... -
Structure of the Flow Field of a Nonpremixed Gas Jet Flame in Cross-Flow
(The American Society of Mechanical Engineers (ASME), 1997)Experimental studies on nonpremixed turbulent flames in cross flow are necessary as the current analytical and numerical tools are unable to provide acceptable quantitative information about their ... -
Numerical/Experimental Analysis of an API 8-Round Connection
(The American Society of Mechanical Engineers (ASME), 1997)The objective of the research reported in this paper is to investigate in depth the performance properties of the 5 1/2-in. 14-lb/ft J-55 API 8-round short thread casing connection under ... -
Study of Hydration During Curing of Residues From Coal Combustion With Limestone Addition
(The American Society of Mechanical Engineers (ASME), 1997)The hydration reactions that occur with CFBC materials treated via the CERCHAR hydration process and combined with PFA have been examined and compared with materials produced via the LIFAC ... -
Petroleum Coke and Coal Start-Up Testing in Bubbling Fluidized Bed Combustors
(The American Society of Mechanical Engineers (ASME), 1997)Bench-scale and 160 MWe demonstration tests were conducted for petroleum coke and high volatile bituminous coal blends. The bench-scale apparatus was a 100-mm-dia reactor located at the Canada ... -
Improving the OTEC Power Plant Performance by Metal Hydride Energy Systems
(The American Society of Mechanical Engineers (ASME), 1997)A new system to improve the present OTEC (ocean thermal energy conversion) power plant performance is here presented. This is a metal hydride energy system operating as a “temperature upgrading” ...