Journal of Energy Resources Technology: Recent submissions
Now showing items 1621-1640 of 3450
-
Laser Induced Plasma Spectrometry With Chemical Seeding and Application to Flow Mixing Analysis in Methane–Air Flames
(The American Society of Mechanical Engineers (ASME), 2015)Spectroscopic measurements of flames are amongst the most important analytical diagnostic techniques that allow one to improve thermal and energy efficiency of industrial furnaces. A chemical seeding laserinduced plasma ... -
Combustion and Emission Characterization of n Butanol Fueled HCCI Engine
(The American Society of Mechanical Engineers (ASME), 2015)Biofuels are attracting global attention as alternate transportation fuels due to advantages of their being produced from locally available renewable resources, lower pollution potential, and biodegradable nature. Butanol ... -
Significance of Transient Exergy Terms in a New Tray Design Solar Desalination Device
(The American Society of Mechanical Engineers (ASME), 2015)An investigation of the transient exergy property term, exergy storage, for a new desalination tray design was performed. It was illustrated that exergy destruction rates provide a means of comparing alternative energy ... -
On the Modeling of Steam Methane Reforming
(The American Society of Mechanical Engineers (ASME), 2015)Modeling and simulations of steam methane reforming (SMR) process to produce hydrogen and/or syngas are presented in this article. The reduced computational time with high model validity is the main concern in this study. ... -
Evaluation of Explicit Coupling Between Reservoir Simulators and Production System
(The American Society of Mechanical Engineers (ASME), 2014)In recent years, the oil industry has used various methodologies to solve numerical coupling of reservoirs and production systems to properly model complex projects needing an integrated solution of computational models ... -
Disjoining Pressure and Gas Condensate Coupling in Gas Condensate Reservoirs
(The American Society of Mechanical Engineers (ASME), 2014)Porescale coupled flow of gas and condensate is believed to be the main mechanism for condensate production in low interfacial tension (IFT) gas condensate reservoirs. While coupling enhances condensate flow due to transport ... -
Numerical Simulation of Complex Fracture Network Development by Hydraulic Fracturing in Naturally Fractured Ultratight Formations
(The American Society of Mechanical Engineers (ASME), 2014)The creation of large complex fracture networks by hydraulic fracturing is imperative for enhanced oil recovery from tight sand or shale reservoirs, tight gas extraction, and hotdryrock (HDR) geothermal systems to improve ... -
Enhancing Oil Recovery With Bottom Water Drainage Completion
(The American Society of Mechanical Engineers (ASME), 2014)Field trials and physical modeling of wells with downhole water sink (DWS) completions have demonstrated controlled water coning and increased oil production rate. However, no field trials were long enough to show DWS ... -
Influence of Radial Flux Inflow Profile on Pressure Drop of Perforated Horizontal Wellbore
(The American Society of Mechanical Engineers (ASME), 2014)In this study, the authors have attempted to present five different profiles for a uniform radial influx through a perforated wellbore. The total pressure drop is not only frictional, accelerational and gravitational ... -
Effect of Drillstring Deflection and Rotary Speed on Annular Frictional Pressure Losses
(The American Society of Mechanical Engineers (ASME), 2014)Keeping the drilling fluid equivalent circulating density in the operating window between the pore and fracture pressure is a challenge, particularly when the gap between these two is narrow, such as in offshore, extended ... -
Gelation Performance and Microstructure Study of Chromium Gel and Phenolic Resin Gel in Bulk and Porous Media
(The American Society of Mechanical Engineers (ASME), 2014)Polymer gel has been widely used to control excessive water production in many mature oilfields; however, there still exist some problems concerning the differences between gelation behavior in bulk and porous media. In ... -
Experimental Study of the Impact of Drilling Fluid Contamination on the Integrity of Cement–Formation Interface
(The American Society of Mechanical Engineers (ASME), 2014)Flood experiments were conducted over 30day periods at 14.48 MPa (2100 psi) confining pressure and temperature of 22 آ°C (72 آ°F) with cement–sandstone composite cores and brine at a flow rate of 1 ml/min. ... -
Shale Caprock/Acidic Brine Interaction in Underground CO2 Storage
(The American Society of Mechanical Engineers (ASME), 2014)Shale caprock integrity is critical in ensuring that subsurface injection and storage of anthropogenic carbon dioxide (CO2) is permanent. The interaction of clayrich rock with aqueous CO2 under dynamic conditions requires ... -
Simulating Multizone Fracturing in Vertical Wells
(The American Society of Mechanical Engineers (ASME), 2014)Numerous multizone multistage hydraulic fracturing treatments are now being executed in low permeability oil and gas fields around the world. Due to the limited access to the subsurface, posttreatment assessments are mainly ... -
A New Comprehensive Model for Predicting the Pressure Drop of Flow in the Horizontal Wellbore
(The American Society of Mechanical Engineers (ASME), 2014)Over the past two decades, the modeling of flow in a perforated pipe with influx through wall openings has been recognized as a key topic especially in the field of horizontal wells. In this paper, based on the theoretical ... -
Modeling Pore Continuity and Durability of Cementitious Sealing Material
(The American Society of Mechanical Engineers (ASME), 2014)In this paper, results of a numerical study on pore continuity, permeability and durability of cementitious slurries for carbon sequestration projects are presented. The hydration model Hymostruc is used to simulate and ... -
Annular Frictional Pressure Losses During Drilling—Predicting the Effect of Drillstring Rotation
(The American Society of Mechanical Engineers (ASME), 2014)Controlling the annular frictional pressure losses is important in order to drill safely with overpressure without fracturing the formation. To predict these pressure losses, however, is not straightforward. First of all, ... -
Experimental Study of Reasonable Drawdown Pressure of Horizontal Wells in Oil Reservoir With Bottom Water
(The American Society of Mechanical Engineers (ASME), 2014)For the development of oil reservoir with bottom water, it is significant to analyze the impact of drawdown pressures on post water breakthrough performance of horizontal wells. Based on a smallscale and discretized physical ... -
Need for Engineering Solutions to Problems Associated With Offshore Oil and Gas Production
(The American Society of Mechanical Engineers (ASME), 2014)There has been an increase in oil spill research and development, especially after the Deepwater Horizon accident in the Gulf of Mexico. However, the public resources seem to be concentrated in the life sciences, rather ... -
Modeling Oscillatory Behavior of Electrical Submersible Pump Wells Under Two Phase Flow Conditions
(The American Society of Mechanical Engineers (ASME), 2014)The effect of free gas on electrical submersible pump (ESP) performance is well known. At a constant rotational speed and constant liquid flow rate, a small amount of gas causes a mild head reduction when compared to the ...